Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing dining table that will have a Vinyl Decal

Featured Replies

Completing a 90" x 44" dining table.  The table is a trestle table built from solid hard maple and walnut.  The sent of the table is a 20 1/2" x 75" walnut surround by hard maple.  Was planning on natural, so was not planning on applying a stain.  Several questions here.

Was originally planning on applying General Finishes Arm-A-Cell in clear then a bunch of coats of Arm-A-Seal oil & urethane topcoat. 

Then had some concerns with the walnut had some different tones.  Was think if a pre-conditioner wood help even out the look.  I was told in past that a pre-conditioner is only used before staining.  I am not familiar with using multiple finishes.  Such as a initial coat of boiled linseed oil, then multiple coasts of shellac with a few final layers of wiping varnish.

The table will be heavily used within a kitchen of a fire station.  The patch of the fire station will be put on the center of the table by a vinyl sticker.  There will be clear areas of the vinyl and the decal is transparent so you can see the wood grain thru. 

After would is sealed then decal is attached, concern with building up around decal so you can not feel edge.  Will the urethane effect the vinyl.  Concern adhesive of topcoat to decal and around edge of decal. 

Any recommendations and advice would be much appreciated. 

You're kind of mixing up Arm-R-Seal and Seal-A-Cell...but I'll assume you're talking about Arm-R-Seal.

IMO walnut doesn't really need help in the color department...I've always been happy with what it looks like with nothing more than ARS.  Color-match issues should be addressed during material selection, not during finishing.  Again...IMO.  There are plenty of people who use coloring tricks on walnut, but I'm not one of them so no advice from me on that.

But I wouldn't want to put anything oil-based directly on top of the vinyl sticker for fear that the oil would seep under it and cause adhesion issues.  I'd probably put a coat or two of shellac down first, then topcoat with a few coats of ARS.

I always wondered what finish they use on basketball courts, but have never been in the right position to ask.   I have used floor finish, with great success on table tops, and wooden countertops.  Linseed oil would not be any part of a table top that gets used much for me.   Bona Naturale will lock the color close to where you want it as a first coat, and I have used Bona Traffic Hd after the Naturale for table tops, and counters.   I have also used moisture cure urethane.   But all those finishes are expensive, and I don't think even available in less than gallon sizes.  MCU might come in quarts, but it's about as far from low VOC as you can get.  Any of those finishes would be fine for tap dancing on top of the table.

Naturale is a water borne, acid cure urethane, and am not sure how it would react to adhesive.   I'm sure a floor finish company, or supplier, could tell you what would work.  Someone has a lot of experience with those basketball courts.

 

Just checked what products one of my flooring buddy uses. He uses alot of Duraseal Finishes on his floors and something called Odie's Oil (they make Bloxygen) for his countertops. You will probably have to check with both manufacturers to see if there will be any adhesion issues with the decal. Hope to see some pics of the end result.

 

 

Sent from my SM-G950U using Tapatalk

 

 

 

 

I used general salad bowl finish for a huge walnut countertop one time. Worked awesome, and really brought out the colour in the walnut.

Or

If you have access to hvlp, you may want to consider spraying a high quality water based poly on top - very durable and looks great. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.