Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Dog hole chamfer reamer off of ebay

Featured Replies

I bought this one, but there seem to be a slew of these things on ebay for about $20, including shipping. It's what a call an "optimizing tool" - you could readily chamfer a dog hole with a router, this just does it using a drill and needs no set up, so presumably faster. My goal is just to relieve the edges of my dog holes to prevent splintering and I was curious if this was worth it.

The good: the blade has four sides and can be easily rotated. Once you go through all four sides, I haven't looked for replacement blades, but I suspect it's cheaper to just buy another whole tool. On a hole that is nice and straight, and the surrounding area of the workbench is flat, it does a reasonable job.

The bad: It doesn't ream the hole pass the top ~1/8", so if you have gunk in the hole, it's not going solve that problem. Some of the dog holes on my bench aren't the straightest or the bench isn't the flattest and results are mixed in those cases. If I wasn't careful, it would mar the surface around the hole a bit (worse on skewed holes).

Conclusion: I was surprised it was as well made as it was, but unless you really care more about speed than quality or don't have a router, it is probably worth using a router and saving the $20.

PXL_20250719_150134257.thumb.jpg.b822c9ec097c5316941434208d65becb.jpg

PXL_20250719_150229736.thumb.jpg.bac8f0b106e9ae630e83ded6abb1443e.jpg

Decent job on a decent hole:

PXL_20250719_150334835.thumb.jpg.3f676e6d36d0a2d0608db3e8da208977.jpg

Lousy job on a lousy hole:

PXL_20250719_150415898.thumb.jpg.3826e0cd71e82955ad71e4c33234a965.jpg

That would work, but I just used a router & chamfer bit. Setup was trivial.

I've seen videos of this one by UJK that is a combined chamfer and reamer. TSO & UJK have quite a few dogs that make use of the chamfer, not only for aesthetics. 

On 7/19/2025 at 4:04 PM, drzaius said:

That would work, but I just used a router & chamfer bit. Setup was trivial.

Same. A bearing guided chamfer bit makes it a snap. 

One suggestion, for boring dog holes, i use a 3/4" spiral bit in a plunge router, which ensures it's plumb, and finished what that bit couldn't reach with a spade bit in a drill. 

On 7/19/2025 at 2:24 PM, Von said:

I bought this one, but there seem to be a slew of these things on ebay for about $20, including shipping

Guess I should have followed the link before commenting. The UJK products only come sized for 20mm holes, not 3/4".

1 hour ago, Ron Swanson Jr. said:

Same. A bearing guided chamfer bit makes it a snap. 

One suggestion, for boring dog holes, i use a 3/4" spiral bit in a plunge router, which ensures it's plumb, and finished what that bit couldn't reach with a spade bit in a drill. 

Same, but I used  a Wood Owl bit to extend the holes. I gotta say that I really like those Wood Owl bits.

  • Author
On 7/19/2025 at 6:40 PM, drzaius said:

Same, but I used  a Wood Owl bit to extend the holes. I gotta say that I really like those Wood Owl bits.

+1 for the Wood Owl bits, that's what I've settled on to make my dog holes (and I've learned to use a guide to make them straight).

On 7/20/2025 at 6:49 AM, Von said:

+1 for the Wood Owl bits, that's what I've settled on to make my dog holes (and I've learned to use a guide to make them straight).

+2 expensive but worth it. I also use a collar to insure its straight.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.