Popular Post gee-dub Posted September 20, 2025 Popular Post Report Posted September 20, 2025 Ah yes . . . another DP upgrade. Things to do while you are watching finish cure. My current DP (which I like very much) has a design flaw. The head casting is so thick that changing the factory belt to the lower pulley on the front pulley stack is an exercise in frustration. I know a lot of folks just leave their DP on whatever speed it was when they got it and use everything from 3/32" bits to 3" Forstners at that speed. Say it isn't so . At any rate I had finally had it and picked up a small section of 3/8" link belt to run in that position. Nirvana!!! This is just an example of modifying your shop, work surfaces, and tools to meet your needs. More things I have done to my previous and current drill press . . . Stacked buffing wheels. Important if you use exotics for details or custom pulls. You can finish the process without changing wheels. A shop made depth stop for a drill press that had an annoying one. Shorter handles so that you don't hit the fence. Better lighting for my older eyes. I think this light was $10 or $15 on Amazon. Expanded holddown capability. I love having my fingers somewhere else when I am doing funky things. Endeavor to persevere. 6 Quote
Von Posted September 21, 2025 Report Posted September 21, 2025 Gee-dub, I'm taking the liberty of rotating your depth stop photo into what I think is the correct orientation and re-uploading it since I'm very interested in it. My sucks as well and I plan to either do something like you did or a DRO. Thanks for sharing all your tweaks! And I confess, I never think to change my belt position. Knowing me, I need to put up a reminder of some sort. 2 Quote
gee-dub Posted September 21, 2025 Author Report Posted September 21, 2025 Appreciated. I have a speed chart for whatever DP model I currently have laminated and stuck to the side of the DP. 1 Quote
Mark J Posted September 21, 2025 Report Posted September 21, 2025 How did changing to the Link Belt solve your access problem? I didn't get that. 1 Quote
Popular Post gee-dub Posted September 21, 2025 Author Popular Post Report Posted September 21, 2025 On 9/21/2025 at 7:34 AM, Mark J said: How did changing to the Link Belt solve your access problem? I didn't get that. The factory belts are 1/2" monos. The 3/8" link belt (or mono if you prefer those) seats lower into the pulley groove and provides more clearance. The factory belt would just not fit between the head casting and the lowest pulley without a lot of back and forth fighting through the tight squeeze. The 3/8" has about a 1/16" of clearance at the worst location when changing and that's all I needed 4 Quote
Popular Post gee-dub Posted September 21, 2025 Author Popular Post Report Posted September 21, 2025 ***Disclaimer*** I have been a nerd for most of my life. I was trying to work on something in the shop and just couldn't get the noise in my head to stop about belt or band changes. Granted your machine's design will make this apply a little, a lot, or not at all. On my current unit you pop the hood (notice I have a pulley speed chart stuck right to the side of the machine). You loosen the motor positioning rods; there is one screw lock on each side. You pull the handle forward to loosen the belts. You change the belt positions. Pivot the tension handle and lock the travel rod. Close the lid and drill away. Even taking the pictures, per the timestamps on the pics this took me less than a minute. Not bragging, just sayin'. 3 Quote
Popular Post Ron Swanson Jr. Posted September 21, 2025 Popular Post Report Posted September 21, 2025 Besides the obvious safety reasons, the other reason to match the speed with your bit and material is bit preservation. Running a forstner at high speed will dull out down very quickly. 3 Quote
Coop Posted September 22, 2025 Report Posted September 22, 2025 On 9/21/2025 at 12:59 PM, Ron Swanson Jr. said: Besides the obvious safety reasons, the other reason to match the speed with your bit and material is bit preservation. Running a forstner at high speed will dull out down very quickly. Was not aware of that. How do you determine the speed per the size of the bit? Quote
Popular Post gee-dub Posted September 22, 2025 Author Popular Post Report Posted September 22, 2025 On 9/21/2025 at 8:17 PM, Coop said: Was not aware of that. How do you determine the speed per the size of the bit? There are plenty of others but here is one from Wood Magazine. I keep a few charts in plastic sleeves clipped to the inside of my drill press wall cabinet. Screw pilot and through hole sizes and that sort of thing. drill bit speed chart.PDF 5 Quote
Popular Post Ron Swanson Jr. Posted September 22, 2025 Popular Post Report Posted September 22, 2025 My DP came with a chart installed under the hood.... 6 Quote
Enzo Caleb Posted October 28, 2025 Report Posted October 28, 2025 Nice upgrade. Link belts are a smart fix for that kind of design issue, smoother operation, easier adjustments, and less vibration. It’s amazing how small tweaks like this can make shop life so much better. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.