Popular Post Bill Tarbell Posted October 1, 2025 Popular Post Report Posted October 1, 2025 UV-curing finishes like Clean armor, Vesting, Solarez, etc are impressive looking but rather expensive at ~150 a quart. Anyone have any experience with generic UV craft resin from amazon? At $25 a qt is a more reasonable price for a hobbyist. I'm really curious who has tried it so far and how it went. I only found one person trying it out for woodworking on youtube: 3 Quote
Popular Post Bill Tarbell Posted October 2, 2025 Author Popular Post Report Posted October 2, 2025 Well, i did a pile more research and still didn't find anyone else trying this out on wood. I decided to buy some and will give it a whirl this weekend to see if there are any adhesion issues (will putting down sanding sealer help/hurt?). Also curious how it does when applying over stain. Some other general info from the research: resin for 3d printers is a bit cheaper ($17/qt) than that for jewelry. However, the 3d printer resin results in having some kind of oily film that needs to be cleaned off with alcohol. Seemed like the extra hassle and VOC wasn't worth the small savings. Most jewelry resins report as having an 80D hardness, which is equiv to the hardness of a hard hat/helmet. (couldn't find Shore Hardness ratings for any woodworking finishes.. presumably because the hardness ratings are more for thick materials than surface films?) not all jewelry uv resins are equal. There are a few videos comparing brands that were rather helpful. Some characteristics worth considering: yellowing, cure time, hardness, bubbles during cure, odor The two brands i came away with thinking were superior were JDiction and Let's Resin. Both are roughly same price at $40 a quart (compared to $25 for the cheapest stuff) I bought the JDiction 'new formula'. It seemed to be the most popular brand, and the new formula model has reports of having effectively no smells during curing. Most formulations have a semi-strong smell during curing as that's the only time the products release VOCs. The smells supposedly only last a few minutes, so nothing like the days we have to endure with oil based poly. can apply multiple coats sands well 1 qt of resin goes considerably further than 1 qt of poly since there are no solvents to flash off. It should cure just fine with a cheap $10-20 uv light from amazon.. there's seemingly no need for the $200-700 lights that the woodworking brands market/sell since we're just curing such a thin layer of material. .. jewelry and 3d models are super thick and still only take a minute or two with the light.. our paper-thin layer should be seconds even with a cheap light. 3 Quote
Mark J Posted October 2, 2025 Report Posted October 2, 2025 I'm reading along with interest, Bill. Quote
Popular Post Bill Tarbell Posted October 4, 2025 Author Popular Post Report Posted October 4, 2025 Well, i gave it a go and was pretty impressed. I only used a blue shop towel as a brush since i wasn't quite sure what to expect and didn't want to waste brushes. I bought the JDiction New Formula. A quart (1000g) is currently $35, though i bought 400g at $20 for the test. https://www.amazon.com/dp/B0C2PWJ4FN 200g, 300g, 400g https://www.amazon.com/dp/B0CLGBW9GK 1000g At full strength i'd say it is too thick. It's roughly the same viscosity of a standard 2 part epoxy, which you'd normally spread rather than brush on. I applied 2 coats, trying to avoid making it super thick and was a bit underwhelmed. The big issue being it didn't have good leveling properties unless you really lay it on thick like you would epoxy. Though, you can hit it with a torch to pop any bubbles. Hitting these layers with the light for even 5 seconds made it so that the piece was able to be handled. 30s was typically good and solid and 60s was seemingly a guarantee. I then found someone in the fly fishing world that was thinning this stuff with alcohol without curing issues. I gave it a whirl and whipped up some 70/30 wiping solution and was pleasantly surprised. It wiped and generally acted exactly like wipe on poly. Except, with these super thin layers you only need 5-10s of curing time with the light and you're ready for another coat. I tested on birch and pine plywood. I found that neither had adhesion issues. I even whacked it with a hammer to see if it'd crack and flake, but it simply dented with the wood. It felt about the same as poly when hitting it with sandpaper. However, i was able to press my fingernail into the super thickly applied test piece only 60s after it was applied and it resisted denting.. something you wouldn't dare do to thick poly for closer to a few weeks. I also applied it over oil-based stain. I was initially going to test applying it over wet and then over dry stain 24h later ... but i found the extra test wasn't even necessary. I applied some stain straight to the birch and also on top of 1h dry prestain conditioner. I then wiped off the stain and immediately applied the 70/30 UV resin to the stained areas. I had no issues with it pulling up or affecting the stain. It dries completely clear. Here's a comparison of it against a shelf i did a few days ago with the exact same stain and 2 coats of oil minwax poly. The two glossy sections have 4 (or maybe 5?) coats of wipeon. I knocked it down with 320 after the 3rd coat. If i had applied it with a foam brush Here's the light i was using. I had chosen it since it was usb-C rechargeable, had both wavelengths (though i think only 395 matters), was easy to toggle the power, and easy to wield. It is only 10 watts and it'd be fine for smaller projects or someone willing to spend 5-10 minutes going over a large project. Another thing to keep in mind is that you could just briefly hit it with the light to get it handleable and then move the piece out into the sunlight for an almost-instant cure. The size of light is a personal preference .. but the only thing i can say with certainty is that the $200-700 lights that the woodworking finish companies are selling are completely unnecessary. It cured just fine with my cheap $20 light. https://www.amazon.com/dp/B0FCM8N9TP I recorded a video demo of what i've tried so far. I am not a youtuber and was simply holding my phone, but it should give you the gist. I highly encourage real youtubers to invest in some of these jewelry (and maybe 3d printer) resins and give it a more thorough rundown. It truly feels like the woodworking-branded ones are grandly overpriced and need some competition to bring it down to a more reasonable level. 2 3 Quote
Mark J Posted October 4, 2025 Report Posted October 4, 2025 @Bill Tarbell, thanks for the investigation and report! I gather from your video that the dilution you tried was 70% rubbing alcohol, 30% product. I wonder if other mixes would work, too? Do you have to wait for the alcohol to evaporate before curing--seems like you went right away? When curing the resin, is it that the UV light initiates the curing reaction and curing will then proceed without constant UV lighting, or do you have to keep the UV light on the resin untill all of the material is cured? Do you think this stuff might work to fill a crack in a turning blank? The low viscosity mix would get into a deep crevice, but I'm wondering if the UV light would filter all the way down through the resin. Does the resin have any bonding properties, like epoxy? Quote
Bill Tarbell Posted October 4, 2025 Author Report Posted October 4, 2025 I had actually gone for a 50/50 mix but overshot (real easy to do with such a small quantity). But, yea, it was a mix of roughly a 70-80% denatured alcohol and 20-30% resin. Though, you can seemingly treat it like poly and mix it to whatever consistency you're aiming for. My goal was just to get it so it'd level.. i plan on doing more tests to figure out a ratio that's less watery.. guessing it'd be around 20-30% alcohol? Waiting until the alcohol is fully evaporate would be ideal.. otherwise the finish will cure in a suspended state and end up with additional texture where there was still alcohol. I knew i had no intention of doing any video edits, so i was trying to shorten things up as best i could. I'd be more patient if i were doing another video :) From what i gathered by watching the jewelry and 3d printing folks, it seems that it will not continue to cure without further light. 3d printer people will print their whole model and it will be a solid structure, but tacky.. so they have to put it under a light to finish it off. Hmm... i'd go with regular 2 part epoxy for crack filling. This stuff would work, but it may be hard/impossible to cure product that the light doesn't reach. However, if you left it under the light long enough then i think it'd probably work fine. The 3d printer guys are printing whole models of creatures and the models are even opaque colors. They have to leave it under the light for hours to get it to cure since the light has a harder time penetrating (and i assume the center of the model may never cure, similar to massive concrete structures) I did hear people refer to it as glue. It bonded extremely well to wood, but i think you'd need to be gluing something transparent to be able to properly cure this stuff. Probably another case where regular epoxy would be better. I'm still really hoping this will spur fancy youtubers with fancy budgets to put this stuff through the gauntlet :) 1 Quote
Bill Tarbell Posted October 4, 2025 Author Report Posted October 4, 2025 I continued some testing today. Not good. I left the pieces from last night out in the sun for a couple hours just to see if anything would change and give it a confidence cure. I also let the tub of left over mix cure in the sun... and it turned into a very rubbery material. Possibly because their was still unflashed alcohol in the mix? shrug. I then cured a puddle of 100% resin, 75%, and 50% resin mixtures. Again, the alcohol didn't get a chance to evap. The mixes were a neat rubbery texture, possibly useful for something, but certainly not for wood finish. The 100% was nice and hard, but i could scratch it with my fingernail. I think this rules out the Jewelry resin as being a candidate for wood finish. It's just not resistant enough to scratching. I'm curious.. does anyone here use any of the pro finishes (Clean armor, Vesting, Solarez)? Could you do the fingernail scratch test to see if it is just an issue with uv resin in general? 1 Quote
Ron Swanson Jr. Posted October 5, 2025 Report Posted October 5, 2025 Hi Bill Question for you, is there a particular characteristic you're hoping to get out of this stuff that you're not getting from traditional finishing options? Or just curious about this new stuff and whether it will work? Either way, i enjoy your research. Quote
Bill Tarbell Posted October 5, 2025 Author Report Posted October 5, 2025 The main draws were the low odor and instant cure. I had just stumbled onto a stumpy nubs video showcasing Clean Armor and was intrigued. However, i was too cheap to allow myself to buy it and then went down a rabbit hole of researching alternatives. 2 Quote
Coop Posted October 7, 2025 Report Posted October 7, 2025 Appreciate the research but I think I will stick with West Systems as experience tells me what to expect. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.