Popular Post gee-dub Posted July 27 Popular Post Report Posted July 27 On the current Guest Bedroom Dresser project I had yet another opportunity to use these Torsion Beams. I thought they were from a Fine Woodworking article but I cannot find it . . . maybe it was Woodsmith. As I age the past starts to look like the foggy moors in a werewolf movie. Be that as it may . . . If you have not taken the amount of time available between breakfast and lunch to make a set of these I urge you to do so. They are a simple torsion box assembly made from hardboard and 1/2 MDF. I made a thread about them here. The manufacture of them is easier than it looks and they have proven useful to me for many years. They store in not much space at all . . . They are useful for project support, third hand lifting tasks, and general work around the shop. I was just using them to support something a few minutes ago. I had LOML slide the beam under the carcass while I held it up at one end and then at another. Worked like a charm. 5 Quote
Von Posted July 27 Report Posted July 27 Very nice. I have a variety of not-nearly-as-nice similar work supporting fixtures. It's amazing how often I just want something higher or the ability to get clamps under it. 2 Quote
gee-dub Posted July 28 Author Report Posted July 28 Someone else found this article in Popular Woodworking. The dimensions are a bit different but the construction is the same. 2 Quote
Chestnut Posted July 29 Report Posted July 29 I need to make something like that. I have a small pile of 36" and 48" off cuts that i use in a similar way. Trouble is I don't trust them to stay strait. Every time I use them i joint one face and plane the other parallel. Eventually they will just turn into dust. 2 Quote
gee-dub Posted July 29 Author Report Posted July 29 @Chestnut - Yeah, if you have some 1/4" hardboard and some 1/2" MDF of adequate size in the scrap bin they are pretty easy to make. Like any torsion assembly the key is to create, by hook or by crook, a flat surface to start to build on. Dry assembling one beam with clamps and then leveling it on any surface is the way to go. I used my workbench but a couple of saw horses or work supports can work as well. Just take a little time to shim things until everything is in plane. You can then use that dry assembled beam as the reference surface for your first glue up. Once one is done you swap it for the dry fit parts and move on. They are great for supporting larger carcasses on saw horses so you don't eat up your assembly surfaces just to hold partially assembled things. They also work to raise work at the bench so you can fit clamps under a reliable reference surface. There are a lot of jigs and fixtures out there. I try a lot of them. Some stick and some don't serve me and what I do as well as I thought they might. The trick is to "know when to hold 'em. Know when to fold 'em. Know when to walk away . . . " For storage, as shown, I just bandsawed some slots in some scrap ply to make the arm sections. Then I just pocket holed them to the studs in the wall. Been there for years with a lot of use and no failures. 2 Quote
fcschoenthal Posted July 29 Report Posted July 29 On 7/29/2026 at 12:01 PM, gee-dub said: I just bandsawed some slots in some scrap ply to make the arm sections. That makes a lot more sense now. At first glance, I thought that you just had stickers between them. That would be a lot of loading and unloading to get to the bottom ones. Quote
Popular Post gee-dub Posted July 30 Author Popular Post Report Posted July 30 Sorry guys. I thought I made a thread on these. I mis-remembered . .. I took some old scrap ply, laminated it together, Drew some layout lines for the arms and the rear profiles to miss the mop board and so forth, Counter-bored some holes for 1/4" washer head lags, And screwed them to the studs. I did something similar for my bowed cauls and lighter weight risers but, without laminating the plywood layers. These are simply pocket holed into the studs. 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.