Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Oak Frame and Walnut Splines

Featured Replies

I made this frame for a special picture that my dad had purchased.

I give to you... "Western Swing"

post-2720-0-02741000-1318209673_thumb.jp

post-2720-0-80819000-1318209687_thumb.jp

post-2720-0-49221000-1318209758_thumb.jp

  • Author

I installed the splines then routed the profile on the edge. The profile cut into the walnut splines and exposed them more.. I think it is a good look

take a picture of your jig as well. i'm always interested if someone has come up with a better design than mine.

  • Author

Duck,

Just a simple spline jig. I cut the splines at the correct dimension of where the router bit would cut into it, causing it to be viewed from either angle.

Let me know any questions!

And I do appreciate the compliments everyone!

post-2720-0-17240400-1318271903_thumb.jp

post-2720-0-83299400-1318271962_thumb.jp

Usually I make boxes instead of picture frames. Yours is great for tall stuff but when I’m making long boxes I use a sled that cradles the project in a v between the two miter slots. Wonder if I can figure out a way to add a tall fence on it to cradle tall stuff as well.

Duckkisser,

I made a jig very much like Pbmaster's only it is about 8" deep for making splines in small boxes. I just use the fence on my saw to adjust the distance of the splines on the corners of the boxes. Yes, it will get cut up almost to the point of being useless eventually but, it is so easy to build that replacement will not be a problem.

I suppose a person could design an adjustable stop/fence on a sled that uses the miter slots for location so the blade cut through at the same spot every time but, I think that it will take longer to design and build than it is worth for no more boxes than I build.

Rog

PS. I also have a spline cutting jig just like Pbmasters for picture frames.

ill put a pic on here but its basicly a v shaped trench suspended between two runners. and i just move my stops to the ends of the boxes so my project does no shift much. thinking ill make a biger diamond shaped fence that can be clamped onto the v shaped trench.

but i want to adapt it for doing picture frames and what not plus its easer to move the project around to get that right then it is to get our fence to the right spot every time.

  • Author

Add a higher fence to that stop block and then you put your frame on the high fence... adjust the stop block to the position the frame correctly on the cutting slot.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.