Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

spalted maple and oak box

Featured Replies

Ok folks here is a small box i made as a trade for someone at work. she gave me a router table for this(Router broke in 5 min) took the router to sears and they replaced it with a gift card with a router price that is close to the first one.

http://i1101.photobu...er/P1020886.jpg

http://i1101.photobu...er/P1020885.jpg

http://i1101.photobu...er/P1020884.jpg

http://i1101.photobu...er/P1020882.jpg

How can i get the lid to tighten down some. little bit of gap.

http://i1101.photobu...er/P1020881.jpg

http://i1101.photobu...er/P1020879.jpg

http://i1101.photobu...er/P1020878.jpg

http://i1101.photobu...er/P1020877.jpg

  • Author

hmmm not bad idea problem is what if the top part does not touch the bottom part

I would put a straight bit in the router table and set the height at the same distance as the lip on the top. Set the fence at the same distance as the width of the top piece outside the lip and run the top around all four sides.

As for the bottom, just lay a large sheet of sand paper on the table saw top and put the bottom upside down on it and sand it until all four edges are straight and flush.

If you still have a problem, ask someone else, I'm out of ideas. :D

Rog

Based on P1020881 and 1020878 it looks to me like the lip on the bottom of the lid is just slightly larger than the inside opening of the box right where the lip meets the edge of the top. The gap is pretty uniform all the way around so I don't think your problem is due to a high spot on the lid or box. I looks like the chamfered lip on the lid just isn't dropping all the way down inside the box. I'd try putting a very slight chamfer on the inside opening of the box. Remove very little at a time until the lid seats down tight on the box.

  • Author

soonerdg think thats what im going to end up doing because i cut the lid off on the table saw so it almost perfectly strait.

  • 5 months later...

Looks great. Love the Spalted maple/ oak combo. How did you treat the Spalted maple on this?

  • Author

wow thats an oldie.........just poly at the time i didnt know much about working with finishes so i went with basic what i know.

  • Author

thanks this was a favorite. it ended up being a good project traded it for a router table that the lady had unopened........10 min in router broke so i took to store got credit and traded it in for a plunge router and a sander. 100 doller value so i sold this small box for 100 dollers yaye me

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.