areynoldsre Posted November 29, 2011 Report Posted November 29, 2011 Yesterday my new Lie-Nielsen planes arrived - a block plane, number 4 1/2 smoother and a low angle jack plane. Now I am wondering what the first thing I should do with these are. I've never had decent planes before and am just a tiny bit concerned about damaging them or somehow screwing them up. So if you just received a new set of fancy hand planes what would do with them? Some of my thoughts are:Tune them - flatten, sharpenjust grab a board and start cuttingOil/wax and stare in awe for hours at themBuild a small shrine to them and worship them daily The first project I had planned for them is either a set of boxes (maybe even a blanket chest) or to do more of the cutting boards my family keeps asking for (note that I don't own a power jointer or planner). What would be your first project? And how do you store them?In an old sockIn a fancy custom built cabinetIn the the box they came inIn a safe deposit box at the bank Quote
Torch02 Posted November 29, 2011 Report Posted November 29, 2011 If it is from Lie-Nielsen, then you should be able to use it out of the box. The blade *could* be better with some honing, but will cut right away. If you need to flatten the sole, call them up and send it back - they would consider the sole being not-flat a defect that needs to be replaced. Quote
jhl.verona Posted November 29, 2011 Report Posted November 29, 2011 Yesterday my new Lie-Nielsen planes arrived - a block plane, number 4 1/2 smoother and a low angle jack plane. In a security van? Armed guards? Not jealous at all. So if you just received a new set of fancy hand planes what would do with them? Some of my thoughts are:Tune them - flatten, sharpenjust grab a board and start cuttingOil/wax and stare in awe for hours at themBuild a small shrine to them and worship them daily Option 2. Patience is a virtue after all. Then wax the sole (paraffin wax, couple of squiggles - amazing difference). Then sharpen the blade and do it again. Watch the shavings, and listen to the noise (can't describe it onomatopoeically but you'll know when you hear it). The first project I had planned for them is either a set of boxes (maybe even a blanket chest) or to do more of the cutting boards my family keeps asking for (note that I don't own a power jointer or planner). What would be your first project? Through tenons, so you can chamfer the edges with that block plane Fine tune the number 4 1/2 smoother and plane the boards after the planer, hmmm glossy finish and gossimer shavings. Joint the boards in pairs with that low angle jack plane after the jointer, ever so slightly concave, you'll get terrific glue ups. Warning: remember to stop planing or you'll end up with chopsticks. It's addictive. And how do you store them?In an old sockIn a fancy custom built cabinetIn the the box they came inIn a safe deposit box at the bank Paste wax or mineral oil, then somewhere dry. Socks are good, also mantelpiece, bed side table... John Quote
ChrisG Posted November 29, 2011 Report Posted November 29, 2011 DO NOT FLATTEN THEM! The specs that they are flattened to are plenty flat enough and you risk throwing them out of square if you flatten them. DO SHARPEN THE BLADE! I have yet to see a blade that comes anywhere near sharp enough for ideal use. Yes they will cut, but not nearly to the level or with the ease thay are intended DO ENJOY USING THEM ON A PROJECT! If you've never built anyting by hand before start with something small. Less to flatten and less wood wasted if you mess up. Perhaps a small, simple tools chest to store them in - that would take care of your last question. DO CLEAN THEM OFF AFTER USE! Wipe them down with camelia oil, wax, or whatever. You' dbe amazed at how fast ones body chemistry can rust a plane. I think this is more important then where you store them. Keep them dry and it's probably best that you do not sleep with them (tempting as it may be) or store them in the freezer. I store mine under my bench, they don't stay as clean as I would like, but the shavings and saw dust don't hurt them. Oh yeah! Congrats on your new tools! Quote
Onboard Posted November 29, 2011 Report Posted November 29, 2011 Watch the shavings, and listen to the noise (can't describe it onomatopoeically but you'll know when you hear it). I thought it was “snick”. Quote
ChrisG Posted November 29, 2011 Report Posted November 29, 2011 I thought it was “snick”. Actually it's schiiiiiiiiiiiiiiiiiiiiick... 1 Quote
Onboard Posted November 29, 2011 Report Posted November 29, 2011 Actually it's schiiiiiiiiiiiiiiiiiiiiick... That’s for a long board. 2 Quote
ChrisG Posted November 29, 2011 Report Posted November 29, 2011 That’s for a long board. LOL!!! Quote
Don Z. Posted November 30, 2011 Report Posted November 30, 2011 Honestly, I keep mine in the original box. Mostly because I tend to move around a lot, so they're protected. Also, the box comes with corrosion inhibiting paper. Eventually, I'll finish their custom box. But in the interim... The box they came in. Quote
ChetlovesMer Posted November 30, 2011 Report Posted November 30, 2011 I too, keep mine in the boxes they came in. My intent is to build a nice cabinet for them, but with everything else I have on the project list, I'm just not sure when I'll get there. Quote
nateswoodworks Posted November 30, 2011 Report Posted November 30, 2011 Options 3&4! I have never gotten a L-N or such but my old Bedrocks and Stanleys live in a cabinet built for them. I like glass doors for them so they can look pretty and draw me in to use them even more, like those "I'm running out to the shop for just a minute Honey" times!, I plan on changing out the panels in the other doors since the family has grown! 1 Quote
jhl.verona Posted November 30, 2011 Report Posted November 30, 2011 I plan on changing out the panels in the other doors since the family has grown! Warm dark surroundings, the family grows... Hmm, do you think they'll still multiply if you put glass in? John 1 Quote
areynoldsre Posted November 30, 2011 Author Report Posted November 30, 2011 Options 3&4! I have never gotten a L-N or such but my old Bedrocks and Stanleys live in a cabinet built for them. I like glass doors for them so they can look pretty and draw me in to use them even more, like those "I'm running out to the shop for just a minute Honey" times!, I plan on changing out the panels in the other doors since the family has grown! I am going to build me one of them. That's the way to store planes. Quote
Mister Pants Posted December 1, 2011 Report Posted December 1, 2011 DO NOT FLATTEN THEM! The specs that they are flattened to are plenty flat enough and you risk throwing them out of square if you flatten them. Hehe, I'd been listening to old back eps of woodtalkonline and Matt talked about doing just that with iirc his Veritas smoother and he bananed the sole. Had to send it back for repair and got a nicely worded note from Robin Lee . Quote
ChrisG Posted December 1, 2011 Report Posted December 1, 2011 Hehe, I'd been listening to old back eps of woodtalkonline and Matt talked about doing just that with iirc his Veritas smoother and he bananed the sole. Had to send it back for repair and got a nicely worded note from Robin Lee . The Schwarz blogged about that very situation a while back - http://www.popularwoodworking.com/woodworking-blogs/chris-schwarz-blog/plane-soles-ham-hands-make-iron-bananas Quote
Mister Pants Posted December 2, 2011 Report Posted December 2, 2011 the very very same situation if I remember right. Mr Papnicolao was Matt Quote
nateswoodworks Posted December 4, 2011 Report Posted December 4, 2011 Warm dark surroundings, the family grows... Hmm, do you think they'll still multiply if you put glass in? John When I leave the shop for the night I put on mood music, turn off the lights, and hope for the best! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.