Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Trying to install zero clearance on my TS and it rubs against it now.

Featured Replies

Sounds to me like the blade is not perfectly square, but it could be out by only 1/128th or 1/64th. Where did you get the ZCI? I've thought about making one a few times, but the tray is so shallow it would be a big pain.

  • Author

It did it with my dado insert too so it's not the blade. The instructions that came with the inserts say that there might be rubbing and to use a file to smooth it out. I guess I'll try that since nothing else seems to work.

I purchased this: http://www.woodcraft.com/Product/2000909/35340/LEECRAFT-RIDGID-R4512-Table-Saw-ZeroClearance-Blade-Insert.aspx

i made a wooden one that i had to hand sand a few spots to get it perfect and not throw my blade off and pinch the wood. just sand/file down a tiny bit because it most likely eather the slot or you blade that is tiniest of bits off.

Sounds to me like the blade is not perfectly square, but it could be out by only 1/128th or 1/64th. Where did you get the ZCI? I've thought about making one a few times, but the tray is so shallow it would be a big pain.

What kind of saw have you got? My first tablesaw was a delta TS-350 (below a contractor's saw) and the insert was about 1/8" thick. I was never able to properly put together a zero clearance insert due to the thinness of the material. Most larger saws though are about 1/2" thick (iirc) so you can make one out of just about anything.

  • 2 weeks later...

Sounds to me like the blade is not perfectly square, but it could be out by only 1/128th or 1/64th. Where did you get the ZCI? I've thought about making one a few times, but the tray is so shallow it would be a big pain.

I made a zcl for an old Craftsman saw my bil has (my old one) It has a shallow "tray"

I just routed a rabbitt around the edge, to leave a thin lip to support it.

Sounds to me like the blade is not perfectly square, but it could be out by only 1/128th or 1/64th. Where did you get the ZCI? I've thought about making one a few times, but the tray is so shallow it would be a big pain.

Another source.

check the sides of the teeth to see if there is any pitch / sap from the wood you've been cutting. I had the exact same thing happen on mine after ripping a bunch of teak (the oils built up on the sides enough to cause that rubbing sounds). Took a metal tooth brush and lightly cleaned each tooth. It helped a lot, but still had to go in and lightly file the sides of the ZCI...

Did you cut the ZCI with this blade? I had a similar and after a few days of use the rubbing went - you might want to clean the blade and or wax it. I just use beeswax.

on listening to this again - it sounds like the blade/teeth is out of true - try a new blade.

Annoying I know !!

good luck!

It would seem to me that after running the blade for a bit, even if it was out of round, the blade would cut away anything that it was coming into contact with and eliminate the noise. I hope not but it could be that you have issues with the arbor bearings.

Mine's been making the same noise for years. It just doesn't matter. Bothered me at first but I got used to it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.