Eric. Posted December 23, 2011 Report Posted December 23, 2011 Well I saved my change in a jar for a year and bought a Kapex this week. Has anyone foregone the Festool hose and attachment and hooked up straight to your main DC with a "regular" 2 1/2" hose? Tricks or tips? Advantages/disadvantages? Any ideas appreciated. Quote
davestanton Posted December 23, 2011 Report Posted December 23, 2011 If you haven't seen it already. 1 Quote
Eric. Posted December 23, 2011 Author Report Posted December 23, 2011 Thanks Dave. I have a 3HP DC with 4" duct. Just wondering if a central DC will work with such a small port on the Kapex. I'm gonna try it, guess we'll find out. Quote
fransikaner Posted December 23, 2011 Report Posted December 23, 2011 Dave: Just popped onto your YouTube. Good on ya mate! I have a Rainbow vacuum cleaner (wet cyclone) for the house and have often wondered how to bring a wet filter medium into the dust collecting equation. The Rainbow uses a turbine attached to the motor in the water chamber to create the vortex. I am sure you had some extensive mucking around to hit the sweet spot. Since you are removing most of the dust in the first stage, I imagine your water changes are much less than the once per use for the Rainbow. This took a lot of thought and creativity - and you did it for a very realistic and affordable monetary investment. Well done!!! 1 Quote
woodwhisperer Posted December 23, 2011 Report Posted December 23, 2011 The way it was aways explained to me is to look at air velocity and volume. Large dust collectors move large volumes of air at a lower velocity and dust extractors/shop vacs move a low volume at a very high velocity. So when you take a regular DC down from a large pipe to 2 1/2", the capacity to pull dust is signigicantly diminished. So i suppose it really depends on how close you are to the source and how powerful your DC is. Best thing to do is test it. You might just find that a cheap shop vac does a better job than the DC. ( Quote
Trip Posted December 23, 2011 Report Posted December 23, 2011 ==> You might just find that a cheap shop vac does a better job than the DC. This is almost always the case for tools with inlets below 2.5 inches. The typical shop-level DC is simply not designed with small inlet service in mind. With some clever ducting, you can get it to work, but it's usually a bit of a hack. I kobbled something and lived with it for a couple of years, then just gave up and got a dedicated FT mini for the chop saw. The shop vac can't be of the truly cheep variety -- you do need to move enough air to keep the kapex 'dust free'. Quote
mds2 Posted December 23, 2011 Report Posted December 23, 2011 If you haven't seen it already. This is great. I subscribed to your channel. I was considering doing something similar in my garage and you just sold me. What shop vac are you using? Are you still happy with your system? Quote
davestanton Posted December 23, 2011 Report Posted December 23, 2011 This is great. I subscribed to your channel. I was considering doing something similar in my garage and you just sold me. What shop vac are you using? Are you still happy with your system? Hi Mds2. Yes, still love my small system. The shopvac is a 1500 watt Vacmaster. 240 volts in Australia, so it is just over 2hp. Quote
mds2 Posted December 24, 2011 Report Posted December 24, 2011 Too things coming to the top of my to do list: 1. Improve dust collection 2. Build mobile base for planer I recently got a dewalt planer like yours. I've been lugging it from one place to another and that is getting old fast. So I was going to Build a cabinet for it that I could wheel around and also use for storage. Also I was going to try to figure out what I could do for dust collection driven by a shop vac. Space is a premium and you've solved a lot of problems I was going to run into. Thanks. Sorry for the thread derail. Quote
davestanton Posted December 25, 2011 Report Posted December 25, 2011 Hi Eric. I have been thinking about your question and also Marc's reply, I think he is right and would like to add that by reducing the diameter of the hose from a 4 inch DC down to a 2.5 inch hose at a blastgate could increase the velocity of the air at the entrance to the 2.5 inch hose, thus giving the best of both worlds. I say this because I notice Festool use a 2 inch hose on their boom arm for a short distance and then reduce down. I think that is the principle with vac hoses. never start small and end up large, always start large diameter and reduce along the way if needed. Quote
Eric. Posted December 25, 2011 Author Report Posted December 25, 2011 Hi Eric. I have been thinking about your question and also Marc's reply, I think he is right and would like to add that by reducing the diameter of the hose from a 4 inch DC down to a 2.5 inch hose at a blastgate could increase the velocity of the air at the entrance to the 2.5 inch hose, thus giving the best of both worlds. I say this because I notice Festool use a 2 inch hose on their boom arm for a short distance and then reduce down. I think that is the principle with vac hoses. never start small and end up large, always start large diameter and reduce along the way if needed. Thanks for the insight, Dave. Yeah, that's what I intend to try. The DC is all torn down right at the moment while I insulate and drywall (finally). So I'll tinker with it as soon as the shop is put back together and let you know how it works. Quote
davestanton Posted December 25, 2011 Report Posted December 25, 2011 If there has to be a vertical you could double up the duty by putting a four inch line down to a floor sweep with it's own blast gate down low. Make a y junction half way up the vertical with a four to two and half inch reducing blastgate that services the kapex. Any dust that fals to lift will fall down to the floor sweep gate and wait till you close the gate to the kapex. Full volume again should lift the settled dust easily when you open the floor sweep gate. Quote
Eric. Posted December 25, 2011 Author Report Posted December 25, 2011 If there has to be a vertical you could double up the duty by putting a four inch line down to a floor sweep with it's own blast gate down low. Make a y junction half way up the vertical with a four to two and half inch reducing blastgate that services the kapex. Any dust that fals to lift will fall down to the floor sweep gate and wait till you close the gate to the kapex. Full volume again should lift the settled dust easily when you open the floor sweep gate. Good idea! I've got some noodling to do... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.