Recommended Posts

Posted

I inherited this jointer from my grandfather, no idea how old it is but I'd say at least 20 years. I have taken it apart and cleaned it up but now that I have it reassembled I can't get it to joint two 90 degree faces. This isn't a new issue but the one that forced me to try and repair/fix it. The outfeed table is fixed, no adjustments and with a 38" straightedge on it (and the infeed) I see a slight valley in the middle.

Using the methods I saw Marc use in his jointer video (as best as I could with this old tool) I couldn't get a perfectly parallel top, at least not one where there is no light showing beneath the straightedge but I came close to at least making the gap the same across the infeed side. I have not adjusted the blades yet, figured I needed to have the tables set first.

Any suggestions on what I can do to get this issue fixed? Sadly I can't afford a new jointer and really don't want to be without one. Thanks in advance.

Posted

If you are talking about bringing the tables into co-planer that is only one part of the equation, they can be out a couple thousandth’s and you won't notice it. I would make sure that the knives are parallel to the out feed table first then, make sure that your fence is 90˚ to the out feed table. It sounds like one of those two things may be the culprit.

Posted

Thanks jsiard, since posting this I did some more research and was beginning to think that maybe it was one of the knives no setup correctly. I'm 99.999% certain that the fence is not the issue. I could see it being off a degree or two but not what I'm seeing. I'll report back once I've configured the knives.

Posted
I inherited this jointer from my grandfather, no idea how old it is but I'd say at least 20 years. I have taken it apart and cleaned it up but now that I have it reassembled I can't get it to joint two 90 degree faces. This isn't a new issue but the one that forced me to try and repair/fix it. The outfeed table is fixed, no adjustments and with a 38" straightedge on it (and the infeed) I see a slight valley in the middle.

You may want to consider putting some brass shims under the end of the outfeed table by the cutterhead to allow it to be truly coplanar with the infeed table.

Posted

The outfeed table is fixed, cast as part of the base. Yes, I'm certain of this, I've looked more then once, no seam and no nuts or screws to adjust. The infeed table is adjustable but the problem is I can't make the infeed table high enough to allow me to run a straightedge off the outfeed and onto the infeed and close the gaps near the cutters.

Two questions about the brass shims:

  1. Why brass?
  2. Where can I find these? Is this something I can get a local Home Depot or Lowes or do I need to go to say Woodcraft?

Thanks!

Posted

Its very common to have to shim a older dovetail way jounter outfeed table. You will have to search on line for some place that sells shim stock. But by the sounds of it you cant shim anyways. If you did "fix" your infeed and shim as needed you would never be able to move it. That may not be so bad if it saves the machine, set it to 1/16 shim and forget. I dont have the links but I do recall some pretty good vidios on the web show how to shim a jointer, maybe give google a shot. Shimming is sort of a thing of the past with the advent of parallelogram jointers

Don

Posted

Two questions about the brass shims:

  1. Why brass?
  2. Where can I find these? Is this something I can get a local Home Depot or Lowes or do I need to go to say Woodcraft?

1. Brass can be made quite hard, so the shim won't flatten further over time, and it doesn't corrode. In a pinch, you could also cut apart a soda can and use that.

2. McMaster-Carr is a great source for stuff like this. This link should take you to the brass shims. http://www.mcmaster....s-shims/=g8wr0o

Can you post a picture of your jointer? That sounds like an odd way to make a jointer.

Posted

Got it.

On the Old Woodworking Machines website there's some information on Craftsman jointers that match this description. Here's the instruction sheet to one of them. It appears that there are some screws that adjust the infeed table height. If you can't get the table height high enough, you could shim the infeed table higher, which should be easy to do based on the drawing, or find longer jack screws.

597.pdf

Posted

Thanks everyone. I stopped by Woodcraft to see if they carried any shims and they suggested McMaster as well. I just verified and the model number I have is 113.20680. I had somewhere found a copy of the manual online but I don't see it listed on that site (I should go post it). I'd love to know what year this was made, going off the serial number (which they indicate contains a date code or something like that) this might be circa 1957.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined