Andrew Pritchard Posted March 6, 2012 Report Posted March 6, 2012 I had been looking at buying a jointer. I have a limited budget, especially as I probably won't be making money from my tools (or at least not this one). I'd read various articles and reviews of bench top jointers, but none of them had been particularly complimentary. Most of them complained about the power of the motor when dealing with harder woods. So when I saw an advert for an old jointer at a knock down price, I decided to go for it. It's a rather old Craftsman cast iron jointer. I've done a few test pieces with it, and it certainly seems to do the trick. I have however noticed a slight problem: The previous owners haven't been very kind to the surfaces of the feed in, feed out and fence. See the images below: My question(s) is this: Does it matter that the surface isn't so shiny I can see my face in it? There was some dirty coming off the pieces when I did the tests, but I can clean that up. In order to preserve the surfaces - is there a recommended tool/abrasive? Wire wool for example? I've seen Marc recommending Renaissance Wax was a way of preserving and lubricating surfaces - would this help prevent this level of rust and dirt on the surfaces in future? Quote
dwacker Posted March 6, 2012 Report Posted March 6, 2012 Sand it down with your RO sander and give it a coat or two of wax. The wax helps protect and make the wood move easier. Don Quote
Andrew Pritchard Posted March 6, 2012 Author Report Posted March 6, 2012 Sand it down with your RO sander and give it a coat or two of wax. The wax helps protect and make the wood move easier. I'm going to need a random orbit sander first What grit paper do you recommend? Quote
dwacker Posted March 6, 2012 Report Posted March 6, 2012 I'm going to need a random orbit sander first What grit paper do you recommend? 220 should do it. Wrap some around a block and do it by hand. It wont take very long. Don 1 Quote
Andrew Pritchard Posted March 6, 2012 Author Report Posted March 6, 2012 220 should do it. Wrap some around a block and do it by hand. It wont take very long. Don Thanks Don! And you just disappointed my wife - she was reasoning that if I had to buy yet another power tool, she should be allowed a new handbag! She'll get her new hand bag sooner or later when I get an RO sander. But in the mean time I'll do it by hand. I'll get to know the tool a bit better if I do it by hand. Quote
Chuck M Posted March 6, 2012 Report Posted March 6, 2012 I just got your jointer's twin a week ago. Mine had been in storage for 7 years, it was my grandpa's. I've been using steel wool to clean up the rust. Quote
wilburpan Posted March 6, 2012 Report Posted March 6, 2012 Does it matter that the surface isn't so shiny I can see my face in it? There was some dirty coming off the pieces when I did the tests, but I can clean that up. No. In order to preserve the surfaces - is there a recommended tool/abrasive? Wire wool for example? I've used Norton 3X sandpaper. Wrap it around a block, like Don mentioned above, but I used a long block (actually, a piece of 2x4 I flattened and ran through a planer) to help me cover more ground at a time and to minimize any unevenness that I would do to the table from sanding in one spot too long. I've seen Marc recommending Renaissance Wax was a way of preserving and lubricating surfaces - would this help prevent this level of rust and dirt on the surfaces in future? I used regular paste wax that I usually use for finishing. Renaissance Wax is great, and will do a fine job, but I didn't have any on hand. Quote
Pbmaster11 Posted March 6, 2012 Report Posted March 6, 2012 I have this jointer as well... I had to do the same thing. Quote
DennisL Posted March 7, 2012 Report Posted March 7, 2012 I'v got an old JJ6 that I've been trying to restore. I was worried about putting a low spot in it with my RO, so I've been pushing my granite block back and forth. My arms are super tired but I did actually find a low spot that I had to take out on the outfeed, so I guess it was worth it. Quote
kyleheon Posted March 7, 2012 Report Posted March 7, 2012 Looks identical to the ones inherited last fall. I used ROS with 60 grit and worked up to 220. Waxed and polished, nice and slick. Now if only I could get it the table coplanar. Need to sharpen the blades too. Quote
Andrew Pritchard Posted March 7, 2012 Author Report Posted March 7, 2012 I feel a lot better about buying what could have been a pile of junk. I was dreading people saying "don't touch with a barge pole!". Quote
AndrewPritchard Posted April 3, 2012 Report Posted April 3, 2012 I was persuaded to buy an RO sander (mainly cos they were half price at the time) and I've manage to get the surfaces pretty smooth. They feel smooth to my hand, which I figured was pretty good. I'm glad that I didn't find any low spots on any of the surfaces. I'll post pics when I get a little time. I was going to change (or sharpen) the blades - but they seem to have rusted in place. I've manage to get the locking screws out without too much difficulty, but the blocks that hold the blades in won't budge. Any thoughts anyone? (Curses Facebook for not letting me log in!) Quote
dwacker Posted April 3, 2012 Report Posted April 3, 2012 Soak with PB Blaster you can get it at most any auto parts stores. Don Quote
AndrewPritchard Posted April 4, 2012 Report Posted April 4, 2012 Judging by the comments on the Canadian Tire website, PB Blaster is awesome. I'll give that a go. I've also noticed that when I run my hand over the surfaces I've just sanded with my RO, I'm getting a very fine quite dark grey dust on my hand. Is that to be expected, and is it going to be a problem? Quote
kyleheon Posted April 4, 2012 Report Posted April 4, 2012 That is from the sanding I would imagine. Clean up the surface and use some 0000 steel wool. Quote
Andrew Pritchard Posted April 7, 2012 Author Report Posted April 7, 2012 Having soaked one of the sets of knives for three days, and the gentle application of some percussive maintenance I've managed to get one of the knives out. I suspect my hammer will be needed for the other two as well. On the plus side, my jointer is looking better and better. I've re-sanded the feeds and they don't look so grimmy and are even more smooth. As soon as it's all done, I'll post some pics Quote
Andrew Pritchard Posted April 11, 2012 Author Report Posted April 11, 2012 It's taken me a week of soaking the wedges with Liquid Wrench (the stuff the local Home Hardware sold me in the end) and not so gentle application of my hammer and a screwdriver. I broke the end off one screwdriver - a cheap vanadium chrome one which already had a chipped end and I've not used in years so no real loss there. Finally I've got all three wedges out, de-rusted and the new knives in. I've run a bit of 2x4 through to see how it runs and it's looking good. However I'm struggling to get the fence square to the out feed. I can get it square, but when I tighten the knob on the side it comes out of square by a degree or so. Any one got any advice for me? Quote
wdwerker Posted April 15, 2012 Report Posted April 15, 2012 I have one of those old Craftsman joiners that I don't use any more. I think your fence problem is the metal tilt plate gets a ripple in it where it has been tightened slightly wrong over the years. I took mine off and hammered it out flat again. I think I remember a cone shaped washer went underneath? It takes a lot of patience to adjust the knives. Good Luck Steve Quote
Andrew Pritchard Posted April 15, 2012 Author Report Posted April 15, 2012 Adjusting the knives was pretty easy. I raised the in feed until it was level with the out feed using a spirit level, then adjusted the lifter screws until the spirit moved slightly indicating that the knife was just higher than the out feed - as per the instructions that came with the new knives. The metal tilt plate had no locking nut or washer (conical or otherwise) on it at all when I got the jointer, just the bare bolt. I found a spare nut, and a washer to hold that still. It looks like someone has replaced the bolt that controls the tilt on the fence at some point, because it's far too long. I wonder if the arrangement of washers isn't helping the situation. Quote
wilburpan Posted April 15, 2012 Report Posted April 15, 2012 You can always cut down the bolt. Put a nut all the way on the bolt that's too long, and use a hacksaw to cut it to the length that you want. Then spin the nut off the bolt, which should repair any threads that were messed up from the hacksaw. Voilà — custom bolt length. Quote
Andrew Pritchard Posted April 15, 2012 Author Report Posted April 15, 2012 I might just do that, though I don't know if this will fix my leaning fence problem. I thought I'd managed to get it square, and then ran a piece through, only to find I'd pushed it off square again. Cutting the bolt down might help with that little problem. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.