tdale51@yahoo.com Posted May 4, 2012 Report Posted May 4, 2012 First off I'm not sure if this post will qualify as a tool gloat or a product review so I'm posting it here in General Woodworking in hopes that the moderators will sort it out for me. I finally pulled the trigger and bought the Grizzly G0715P to replace my old Ryobi BT3100 table saw. I got tired of having to double and triple check the fence and miter table for every single cut to ensure squareness. I researched table saws for about a year before finally deciding to take the plunge. All my research kept leading me back to this saw being the best saw I could afford that had all the features I wanted in a saw. While researching I watched the newspaper, craigslist w/in a 150 mile radius, and the local paper nothing I liked came up when I had the money for it. I read every review I could find on this saw. A couple I found on lumberjocks said that they would set the miter slots parallel to the blade at full depth of cut and then lower the blade some and somehow the blade was no longer parallel to the miter slot. I called Grizzly tech support to ask them if they were aware of this complaint, and if they were still getting the complaint since this was a deal breaker for me. They told me they were aware of it and the problem had been addressed so I decided to go for it. I placed the order on Wednesday. I only live 3.5 hours from their Muncy, PA showroom but I don't have a truck that I could get there and back for less than the $99 shipping charge. Thursday morning UPS frieght called me to tell me that they wouldn't be able to deliver until next Wednesday because all of their lift gate trucks were down for maintenance until then. So I arranged for a friend to help me pick up the saw from their warehouse 30 miles down the road this morning. When I inspected the boxes the box for the actual saw was in perfect condition, however both the boxes for the fence rails and the fence itself had some pretty significant damage. IMO that's UPS's fault, not Grizzly's. Upon inspecting the contents of the damaged boxes there was no damage to the items within thank goodness. When we got the saw to my house and were lifting it down from his truck the thing slipped right out of my hands and crashed to the ground! After a few choice words were uttered I opened it up to find that the saw appeared to take the two foot fall completely unharmed. I'm impressed! I took my time cleaning all the rust prevention goop off (there's quite a bit of it) and re lubricating all the moving parts before starting the assembly. Then I assembled the saw by myself. To attach the extension tables I clamped a couple pieces of scrap to the bottom of the main table while I bolted the extensions on. From there I followed the extremely well written manual to finish up the assembly. Then at full depth of cut I checked the miter slot to blade parallelism. I don't have a dial indicator so I used an adjustable square. Right from the factory it was dead on. Then just to double check earlier complaints I lowered the blade to about half depth, still perfectly parallel. Now on to the fence. The rails were mounted too low for the fence to slide across the table, user error not machine. I turned my brain on and correctly mounted the rails now the fence slides across the table like a figure skater on ice. I move it up to the miter slot, lock it down and what do you know, perfect alignment. Put the square up to the fence and it's square to the table. I didn't like the gap between the bottom of the fence and the table but that was easily adjusted by tweaking 3 set screws. Next it was on to checking the 90 and 45 degree stops. So outcome the squares again and both stops were perfectly set from the factory. Then I installed the less than substantial factory miter gauge and checked it for square, it was. I then installed the blade guard. It was pretty stiff getting it in and really difficult to pull it out. I couldn't find any adjustments in the manual for this so I started looking around and decided I'd loosen the three screws that hold the guard/riving knife in place. Works beautifully now. I slide a straight edge against the blade and the splitter was not in line with the blade. What do you know there's another easy adjustment for that too! Finaly the moment I've been waiting on for a year now! Time to flip the power switch. It is amazing how quite this saw is! I don't know if it's because it's running on 220 or not but I think it's just slightly more than half as loud as the Ryobi. I shut the saw off and went to grab a nickel. I stood the nickel up on the table and hit the power button again. The nickel didn't even wobble. I put it in several spots around the table and not so much as a wiggle. Now for the real fun. I grabbed a piece of 3/4 walnut and did a quick cross cut using the factory blade. NICE! Perfectly square, very little tear out. Then I set the fence up for a rip cut of the same piece of scrap. Grabbed my favorite push stick and ripped away. Holy cow! no burnt wood smell! and a perfectly square rip! Not to mention the cut looked almost as if I had run a smothing plane accross the board. Man, that's a nice feeling. There are a couple things I don't care for. First the dust collection isn't the greatest but neither is my dust collector so that may be the problem. When I opened the cabinet there was a fair amount of sawdust inside but none got thrown back at me like with the old Ryobi. The only other complaint I have at this time is EVERYTHING is Allen wrench! I would prefer hex bolts. Quote
Wayniackc Posted May 5, 2012 Report Posted May 5, 2012 I just got a Grizzly G0690 in March and I had a similar experience. I was really impressed with how accurate everything was right of the box and how easy it was to assemble. Runs like a champ too, very quiet, and makes great cuts. Quote
knotscott Posted May 5, 2012 Report Posted May 5, 2012 Congrats on the new saw. Really glad to hear that you didn't have the alignment problem. What blade did you install? Quote
tdale51@yahoo.com Posted May 5, 2012 Author Report Posted May 5, 2012 knotscott, thank you. I used the factory blade for the setup. On the off chance that something went horribly wrong I didn't want a good blade to get damaged. Quote
Gordon Allen Posted May 5, 2012 Report Posted May 5, 2012 Great review! And the timing couldn't be better for me; I have also been logging lots of hours of table saw research, and had pretty much decided on this saw as the best one for me. It makes me feel even better about my decision to hear another great review of this saw. Enjoy, and thanks for the write-up! Quote
jmaichel Posted May 5, 2012 Report Posted May 5, 2012 Great review! I have been very close to buying this saw a couple times. I have been looking at table saws for a long time, bought and Ridgid r4512 but took it back the next day because I was not sure if that is exactly what I wanted. I live within 2 hours of a Grizzly showroom and warehouse but have no way to get the saw home. I can order it online but I have to pay tax, shipping and liftgate. My problem is that the cost of the saw plus all to previous mentioned items plus a mobile base, which all adds up just shy of $1100. The $1100 price tag puts me in a new class of saw. It sounds like you made a good purchase and that you are happy with the saw, I might have to rethink the G0715. James Quote
CessnaPilotBarry Posted May 5, 2012 Report Posted May 5, 2012 Isn't ANY new tool that makes us happy a gloat? Enjoy! Quote
tdale51@yahoo.com Posted May 6, 2012 Author Report Posted May 6, 2012 James, If I understand you correctly, you're right, for $1100 you would infact be in a higher class saw. But consider this, you'd have to pay $1100 for the saw and still pay tax, shipping, lift gate and mobile base. Then you'd be looking probably around $1300-1400. Quote
jmaichel Posted May 6, 2012 Report Posted May 6, 2012 James, If I understand you correctly, you're right, for $1100 you would infact be in a higher class saw. But consider this, you'd have to pay $1100 for the saw and still pay tax, shipping, lift gate and mobile base. Then you'd be looking probably around $1300-1400. It depends on where you are buying your saw from. If I am looking at Grizzly then yes $1300-1400 is correct but at $1100 now your talking about General International, Steel City, Jet (the new ones with riving Knives are $1350) and couple others. Most of these can be found online with no tax and free shipping depending on where you are ordering from. I think the G0715 is very nice saw for the money but when you add it up it brings to light a couple other saws that are now within reach. Just my thought process while looking at table saws. Quote
Derrick Posted May 6, 2012 Report Posted May 6, 2012 Thanks for the review! I've also been looking at this saw for a while and had the same concern with the alignment issues so it's good to hear that Grizzly seems to have resolved this. What do you plan on replacing the stock blade with? Also if you get a chance keep us updated on what you like and don't like with the saw over the next few weeks or months. Quote
tdale51@yahoo.com Posted May 6, 2012 Author Report Posted May 6, 2012 James, Good point. The killer for you is Washington's damn 8.1% sales tax.( I don't miss that) Derrick, I don't know what I plan on using to replace the stock blade with. I JUST bought a Freud Diablo combination blade for the Ryobi, unfortunaly it's a thin kerf blade and because of the thickness of the splitter and riving knife I can't use a thin kerf blade. I've found the Freuds to have a good cost to result ratio in the past so I'll probably stick with them. I suppose that could go in the dislike column but this saw has so much more power than what I'm used to I think it'll be some time before I really care. I'll keep you posted on what I do/don't like as my experience warrents. Quote
knotscott Posted May 7, 2012 Report Posted May 7, 2012 James, Good point. The killer for you is Washington's damn 8.1% sales tax.( I don't miss that) Derrick, I don't know what I plan on using to replace the stock blade with. I JUST bought a Freud Diablo combination blade for the Ryobi, unfortunaly it's a thin kerf blade and because of the thickness of the splitter and riving knife I can't use a thin kerf blade. I've found the Freuds to have a good cost to result ratio in the past so I'll probably stick with them. I suppose that could go in the dislike column but this saw has so much more power than what I'm used to I think it'll be some time before I really care. I'll keep you posted on what I do/don't like as my experience warrents. Any chance you can duplicate the riving knife with a thinner one? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.