Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Oak (?) table top problem

Featured Replies

I've trying to persuade my wife that the top of our dining table needs refinishing. There's a lot of coffee rings, the finish is patchy etc. However, I have noticed something else, which I don't think she's noticed yet. There are a couple of cracks between the boards the top is made from.

So my questions are:

1) What is the table top made from? I think it's oak - but I really don't know. Can someone confirm or deny that?

2) More importantly, can I/how do I fix the split?

I think the split has been caused by uneven drying. There's usually a laptop parked in that space, meaning there's a continuous stream of hot/warm air being applied directly to that spot and no where else. There's only one other place where the boards have separated, and that's no where near as pronounced. I think I'm going to have to build a work station or separate table for the laptop to go on.

post-6539-0-47624700-1341139577_thumb.jp

post-6539-0-03055500-1341139581_thumb.jp

as for the laptop get it vented and you wont have too much trouble. the crack could have developed from the boards drying out even from seasonal changes. in the fall it might close back up (move laptop to different spot). but if you do want to refinish it remember alot of tables or veneer over a piece of mdf or particle board so be carefull that you dont sand through on the table. fromt he pictures it does not look like veneer but rather boards put together like floor.

  • Author

I think it's solid wood top. The lines where the boards join wrap all the way round to the under side, and you can see end grain on the short edges of the table.

Marc has a video on how to fix a split on a butcher block ... I wonder if you can use the same method.

In case you decide to fill it, i wouldnt, but if you do lol. Remember to stain your filler to match the table before applying into the crack. I suppose you know this but it can get ugly and messy when done in reverse.

  • Author

I wasn't aware of the need to stain the filler before using it - thanks for that. Makes sense now I think about it. I've moved the laptop and put it on a serving mat to keep the heat off the table. I'll see if the crack goes away on it's own, or at least diminishes.

I think I'd put a tracksaw on that and cut along the glue joint where the crack is. It's obvious there was either a problem with gluing or with one (both?) of the glued edges. You'll be removing the table top to refinish it anyway. As long as you ensure that the kerf you cut takes a bit of both boards, you should end up with an edge you can consider gluing up after planing off the saw marks. Other benefit: the table top is finished so squeezeout will be easy to clean up and not get into the Oak pores, which sucks. Just need to take extra care to get the top surfaces flush on the glue-up.

Other word of warning: if you cut this with a tracksaw (like a purchased one or a circular saw of your own on a DIY track), you already know there's some tension in there that tore apart the joint. When you make that cut with the circular saw, that tension is already there. Use a saw with a riving knife or be sure to start the cut and have someone jam a shim into the kerf to keep it from pinching the blade.

  • Author

My circular saw has a riving knife built in. Not even sure I can even take it off, though it does make it a little awkward to change the blade.

Are you suggesting cutting all the way through the table top, or just cutting a little deeper into the split that's already there?

I'd remove the top from the table base and cut right through along that glue line. Re-glue it up. I might be tempted to let it sit a day cut apart before gluing up to see if the cut remains straight. If not, cut it straight again. By cutting it apart such that the cut removes wood from both boards on the joint, you're effectively re-jointing them in-situ for the new joint.

  • 2 weeks later...

Personally, I would NOT cut the top. The crack looks fairly narrow. I would fill it using Timbermate Wood Filler, which is available from Woodcraft. It is water based, comes in different colors so you can probably match the wood pretty closely.

A few months ago I refinished a 30 year-old dining room suite -- oak table, 2 captains chairs and 4 side chairs. Stripped it to bare wood using Citrus Stripper (Home Depot), followed by sanding -- beginning w 80 grit through 180. Stained it dark walnut (Minwax oil-based), and finished it with 3 coats of General Finishes High Performance Satin water-based finish (sprayed with Earlex 5500). It did not have any cracked boards like you have but had a couple of small dings I filled w Timbermate.

The results were excellent, even if I do say so myself. :)

I would let the wood recover from the heat you were putting on it with the laptop before finishing, but you could begin the stripping process right away. Be careful to always sand across the grain, especially along the crack.

Hope this helps.

Jim

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.