RJsumthn Posted November 27, 2012 Report Posted November 27, 2012 I picked up some old planes at the antique mall yesterday, a Sargent No. 414 Jack Plane and Stanley No. 4. I am going to get them up into working condition and was wondering what kind of edge should put on them. I know that Jack Planes tend to have a radius iron in them and Chris Schwarz recommends that Jack planes have an 8" radius to them. I do want to use the Jack plane to flatten boards but also as a jointer until I can get one of those. I was just planning on putting a straight edge on the Stanley No. 4 but I don't really know for sure if that is what is recommended or not. Let me know what you guys think. Also, how do you put a radiused edge on a blade? Do you know of any good videos that go into this. I don't have a grinder just some stones. Thanks - RJ Quote
rodger. Posted November 27, 2012 Report Posted November 27, 2012 I camber my veritas #4 for general smoothing operations. If the blade is left square, you could get "track marks" on the surface of your workpiece. I use the veritas MKII camber wheel to add the camber. You can do it other ways, including putting pressure on each corner as you hone (count the strokes). http://www.leevalley.com/en/wood/page.aspx?p=54181&cat=1,43072,43078,54181 I have two blades for my stanley #5, one slightly cambered and one square. I use the square blade for jointing with a jointer fence (until I get a jointer plane) and for cleaning up jointed edges from my power jointer. I use the slightly cambered blade for general flattening and smoothing prior to using the #4. 1 Quote
jhl.verona Posted November 28, 2012 Report Posted November 28, 2012 If you use a guide, then light cambers can be applied as franklin pug states - more pressure on the side and count - that's how I do it anyway. Funnily enough I do things the other way round - flat blade for the #4 (but round the corners with a file, that way you won't get plane tracks), and a camber for the #5 for jointing edges. If the edge is out of square, you can use the camber to correct - just move the plane off center a little, otherwise you have to tilt the plane, which doesn't work very well for me. John Quote
Bob Rozaieski Posted November 28, 2012 Report Posted November 28, 2012 Surfacing planes get cambered irons. Joinery planes get straight irons. Quote
RJsumthn Posted November 28, 2012 Author Report Posted November 28, 2012 Ok, I think I'll give the Jack plane a straight iron until I get a second iron or a jointer plane. But for the No. 4 should i sharpen the edge like I would a straight iron then knock the corners down or should I give it a camber from the beginning and if so, what radius should it be (I imagine it would be a pretty larger radius camber). Thanks guys Quote
JayWC Posted November 28, 2012 Report Posted November 28, 2012 I knocked the corners off on my smoothers and left cambering to my jack. I don't have a scrub plane yet so I have two blades for my 5. The first is a relatively large radius. The second is pretty small to use for roughing. Quote
baok Posted November 28, 2012 Report Posted November 28, 2012 I bought the Schwarz video on sharpening in which he describes how to put these edges on your irons. I did it and am quite happy with the results. I have a slight camber on my smoother and a significant radius on my jack. Once I watched Chris do it (several times) it was fairly easy to do it myself although not quick. Quote
jab73180 Posted November 28, 2012 Report Posted November 28, 2012 There is also a video floating around on the internet of schwarz sharpening when he was on roy underhills show. -Jason Quote
RJsumthn Posted November 28, 2012 Author Report Posted November 28, 2012 Jason I have watched that video a couple times. It can be found on the PBS video website under the woodwrights shop and its name Hand Plane essentials i think 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.