Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

beeswax on toboggan

Featured Replies

So, my daughter came home from college on Christmas break and asked if i could help her build a toboggan. How could I resist.... Toboggan is fine, but our mineral oil and beeswax has remained very "tacky." First coat was 3 parts mineral oil and 1 part beeswax. That dried nicely in 24 hours. Second coat of 1 part each is still very tacky after a week. Any suggestions other than rubbing it down to remove any excess (maybe we put it on too heavy) and giving it more time to "cure"? As is I can't imagine it would slide down anything short of a cliff. Maybe it is safer that way....

try spraying cooking spray on the bottom of the runners. put metal runner on it and bring a hot air gun heat up the runners in between runs and it will keep the snow from draging on the surface by melting it at the start into ice :)

I would suggest a top coat of something that will cure. Mineral oil, and bee's wax never really cure, that is kind fo the blessing and curse of a butcher block treatment. They will eventually dry to the touch, but will easily be pulled off with some friction. This is a second hand explanation, so I am not sure how accurate it is, but I was told that mineral oil doesn't penetrate into the wood very far, just the surface. So it is eventually wiped away, or in your case, I assume almost instantly pulls off the wood with the friction of the snow and sled.

I would try a shellac or poly instead the beeswax/mineral oil. If you want the oil, I'd go with BLO (Boiled Linseed Oil) instead of mineral oil. Both look great on the wood, but BLO is supposed to cure, and penetrate deeper. You can get BLO anywhere, I have seen it at every home center in the area, and even Walmart.

Here is another post on the forum from someone who just built one. I think he mentions using an epoxy of some kind.

Don't see many tobaaggons here in South Central Texas, but still have an opinon for ya. If it were me, I would consider a good coat of polyurathane and then wax the botton like skis. Tough hard coat that will be slick when waxed.

i would use the same type of epoxy that they use for table and bar tops give it a nice thick layer to both protect the wood and to give a smooth surface. most sport stores sell ski wax to go on the bottom of ski's its a slick but very hard wax that will create a hard friction less surface. then its all about buffing and layering on more wax and repeating till it is slick.

mineral oil will protect from water but its not a water proof surface protecting medium and bee's wax is too soft a wax.

  • Author

Thanks for your suggestions. A toboggan does a lot of flexing so there would be danger of a hard finish cracking under stress, at least that is what I read elsewhere. Current plan is to rub off and rub in what is there now, possibly with the use of a hairdryer and then apply a harder ski-type wax. I was assuming I'd need to give it a quick touch-up each season, or possibly after each, with the mineral oil and beeswax, but it is seeming too soft and tacky. I was hoping the beeswax would work since it is from my own bees.

Hey Pa,

As Chris mentioned I just finished building one and had all of the same questions / concerns you've brought up. I WAS going to go with an oil / wax finish but decided not for a few reasons.

1) There is no durability. after one run down the hill any kind of wax / oil film will be worn away. Without a film on the bottom it;'s kind of like trying to push sandpaper across wood (lots of friction) = very slow and lots of drag.

2) I wanted to spend more time using it than maintaining it.

Decided to go with 2 coats of rolled on clear epoxy and finished with a satin polyurethane. Looks great, very little maintenance and it's fast! As far as the flexing, providing you don't epoxy the slats together and use only screws (no glue or epoxy) to mount the cross cleats everything will be able to flex without any issues.

If you check out page 2 of the thread Chris linked to at the top, I made 2 videos on it's construction. Part 1 goes over the lumber selection and steam bending process and Part 2 covers the assembly and finishing.

If you have any other Q's please let me know :)

~Andy

Just re-read your original post (finally home for the night) and realized that you've already built it :o ! Post some pics!!! Test it out and see how it works. If the finish could use some "modification" file it away for next Fall's project. But for right now kiss you Daughter on the forehead, ask her to get on the sled and launch her down the hill :P

Or even better, take the maiden voyage together!

Point being, use it while you can.. There will be plenty of time over the Summer to make any necessary changes. Just my humble opinion..

  • Author

Thanks boatworks. I did check out the thread on yours. Very nice! Interesting similarities with the contrasting cross pieces and capped header.

I do hope to try it this winter, but with close to record breaking temps in the 50°'s today and 60°'s tomorrow, it won't be real soon. Also, daughter is back at college....

I spent 90 minutes on it this morning with cloth and hairdryer. We went way heavy on that second coat. I removed excess and I think it will be okay, at least for one excursion, then at least the bottom may be ready for a different finish.

post-8655-0-82478100-1358012950_thumb.jp

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.