Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

first coat of stain and...OUCH! now what?

Featured Replies

Wood material is maple and the stain is Old Masters, oil based wiping stain. I sanded with100 and 180 but the milling cut lines are showing on the moulding,(perpendicular lines to the grain throughout the crown moulding). I didnt notice them until the stain went on. I obviously did a poor sand job. I also sealed with a 1# cut of zinsser sealcoat but still have blotching, was my coat of sealer too thin? not enough drying time? dried 1 hour. I looks terrible. I am going for a much dark color than I have, I know from my test boards a 2nd coat of stain will help with the color but what do I do? Sand it down and start over? The top is veneered plywood. it also blotched pretty badly. I let the stain sit just a few minutes, should it sit longer? I had so much better luck on my test piece. An 8" section is so much easier that a 5' section...haha.. Sealer also did not seal nail holes to keep for darkening, anything to do there?

 

gallery_11710_758_60950.jpggallery_11710_758_178970.jpggallery_11710_758_26436.jpg

Well I for one would not want to try and sand that back to bare wood. A flat surface, sure but all those profiles, no way. I would say there's a pretty good chance things are going to get worse if you try to put another coat of stain on unless you want to go really dark and at that point you should just paint it. If it were me I would probably start over. If was for myself And not a client I might play with it a bit. I might even try just sanding the easy spots and leave the stain in the crevices of the profiles to give it the look of glazing.

I try to stay away from staining if I can. If I am going to stain a project I always use a large sample piece. Hard to tell on a 4"x4" scrap if you're good or not.

Good luck

  • Author

Painting it is too easy... It is for my family room. I guess I'll try to sand the crown portion since that is the worse and light sand the rest.the stain color is very dark like the GF Java

If you have a lot of this to sand, you can use plaster of paris and cast it on a scrap piece. Wait for it to dry, remove the scrap, and then you'll have the perfect profile match. You can then add some self adhesive sandpaper to the bottom.

 

A 1 pound cut of shellac is perfect for a seal coat. Just make sure it is dewaxed shellac. (The SealCoat version is dewaxed). 1 hour dry time is plenty.

 

Finally, you may want to try applying a toner instead of a stain. Toner's tend to not be quite as blotchy.

 

Jerry, I've never heard of not letting the seal coat dry. Could you please explain further the theory behind that? I'm not saying it is wrong, but the only time I've had problem with blotching when using a seal coat is when I didn't let it dry.

I just recently made shelves out of maple. I would think about putting down a second seal coat of shellac. Then applying a dye over top the shellac to even out the color and make it a little darker. The dye will just sit on top of the shellac so you shouldn't get blotching. and you could more easily control the darkness of color. The more and more I woodwork, the more I realize that dyes work a lot more easily than stains to add color. IMO

You skipped 120 and 150 grits which is part of your sanding problems. A profile like that is tough to sand and you don't want to skip grits in that situation. I also lightly sand after applying the shellac sealer before staining.

Where did you buy the moldings? If it was HD or lowes take them back and tell them they are defective. You should not have to sand machine marks out of moulding. Those were cut on with a dull head or are just paint grade moldings.

Id Dye (equalize), seal coat, stain then top coat.

Don

  • 2 months later...

If I were in your place, since you will be placing that in your family room, it's worth giving another shot of sanding. After sanding, fill the holes and finish it better the second time. I think you can still use a light sealant after sanding and maybe a darker sealant as your last option. :) Ana S.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.