Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

non-yellow finish for cottonwood table

Featured Replies

I have built a cottonwood table and want a durable finish but want to leave the color white.  All the finishes which seem to claim they are clear still turn the wood yellow.  Any experience with a white wood and a durable finish?

 

Thanks! 

Crystalac...  It's a water based finish that is tough as nails and does not dis-color (At all)..  On light color woods, it's my go-to finish..

 

Doesn't seem to get a lot of attention or love, but I really like it!  You can get it HERE.  This is for a gallon, but I think you can get smaller quantities.  Only draw back is that it's spray application only.  I believe they have others that can be brushed but I've never used anything other than the Super Premium. 

  • Author

@Boatworks: Great. I had not heard of it until I read some of the other posts. I will definitely check it out.   

 

Would my HVLP sprayer work ok with it?

Also, for a table top how many spray applications would you recommend?  

Given that it is water based I am guessing it will raise the grain and appropriate steps should be taken?

The finish I use adds no color to light woods but they only sell it to professional shops. I tried the Crystalac once and it worked pretty well for me.

Your sprayer should work just fine depending on the size of the tip / nozzle..  I use a 1.2 HVLP on a pressure pot and with experience works great!  Like most water based finishes it's a pretty thin material.  I'd say a tip roughly .6mm would be ideal, but up to 1.2mm can work if you are able to control the flow of the fluid (and practice a little bit :)).  It's pretty forgiving to work with.  I'll spray it until a very light milky appearance then let it cure for an hour or so, then re-coat. 

 

1st application will raise the grain, but if you pre-raise with water and lightly sand with 320 - 400 should be good.  Once the 1st coat is on, sanding with 400 or finer is best between coats (I usually use 600 or a medium scotch bright pad).

 

I checked again and this is the link for what I used.  Super Premium 2001

 

If I remember correctly, I don't think that sanding between coats is REQUIRED, but it never hurts.  I think I always sprayed 4-5 coats, sanded for smoothness and did 1 final coat.  <Done>.  Was able to get all of this on in 1 day.

 

I will say I was very impressed first time I used it.  Coated a push cart that I built out of birch for my daughter when she was learning to walk.  I wanted to keep that crisp color of the white sapwood and darker heart and it worked perfect.  Even did her crib with this as it's certified safe for toys and infant exposure....

 

Since then this cart has been pushed into the counters, walls, etc and the finish has not skipped a beat.  Sure the wood dented, but the finish never let loose and it is very difficult to scratch..  It's been 2 years and the birch is still as crisp as it was the day I finished it..

 

I think you'll really like it!

 

The only thing I don't like about it is that it doesn't bring out the color on dark woods (mahogany, teak, etc).  For light colored woods  it's one of the best I've come across..

 

Hope this helps!

 

~Andy

Crystalac does have a brushable product as well, it is one step down from the Super premium . I have used a foam brush with water bourne finishes before, don't work it back and forth too much. Just flow a stroke on and go back to even it outt. If you work it too much it can get foamy. Let it dry a little longer between coats and sand 320.

  • 2 months later...

is it not the wood itself that will change color as it ages? i believe that is the case in all finishes.

is it not the wood itself that will change color as it ages? i believe that is the case in all finishes.

Most woods will get lighter as they age. Cherry on the other hand will darken with age. The finish however is not apart of the wood and does not lighten ( or darken) but will cure to either blue or yellow. The finish will turn blue for most water based products and CAB Acrylic lacquer. The yellowing is generally seen in oil based products like varnishes and then there is nitrocellulous lacquer.

Below is the best explanation Ive read over the years. Not sure how it will format, ive had it on my computer for a decade but should be readable.

 

Conventional lacquers are formulated principally from the resin known as nitrocellulose. This is a material that is soluble in lacquer thinners, and forms a colorless solution. However, it is too hard and brittle to be a wood finish without plasticizer or modification with a less brittle resin. The choice of this modifying resin determines the color of the lacquer. Inexpensive malaic resin modified products are amber colored lacquers. More expensive coconut alkyd modification produces the so-called water white nitrocellulose lacquer, which is, in fact, also yellow, but not as amber as the malaic modified variety. Furthermore, the dry film of any nitrocellulose lacquer will yellow with age and this property is accelerated by exposure to sunlight.

With the recent and ever increasing popularity of pickle white, solid white, near white and off white wood finishes, a need has been created for truly crystal clear finishes that are also completely non-yellowing on aging. Both white lacquers and clear coats used over white lacquers must exhibit these properties, because a yellowed white finish is aesthetically unacceptable. Lacquers made only from acrylic resin are characterized by a completely crystal clear color and no discoloration or yellowing upon aging or exposure to sunlight. However, they tend to be low in solids, difficult to spray, and have poor solvent release.

CAB is an acronym for Cellulose Acetate Butyrate. Lacquers made from this very expensive resin are also completely crystal clear and non-yellowing. When blended with an acrylic resin, CAB improves solids, sprayability, flow and leveling, and solvent release. The resultant finish is also tougher and more resistant than either resin used alone.

Non-yellowing lacquers made from a complementary, cost-effective blend of CAB and acrylic resins are often called by either name, but are typically a synergistic mixture of the two. Nitrocellulose lacquer materials "fortified" with either acrylic or CAB resins must be used with caution if yellowing is a concern. They may not yellow as quickly, or as much, but they will eventually discolor.

Woodrow "Woody" Sanders is the Technical Information Director at Sampson Coatings, Inc.

Wood is going to do what it wants to do and that includes changing color no matter what is applied on top. All finishes will break down at some point and age. Some finishes have uv protection in them to protect the finish from yellowing and adds a tish of yellow to that finish. Water-based does a better job of not yellowing, than the rest of them.

 

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.