Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Earlex and GF waterbornes - some questions

Featured Replies

I got an Earlex 5500 for a bathroom vanity remodel project and decided to try waterbornes. The lady at General Finishes was very helpful with questions and I'm going to use their water based stain and Endurovar for the topcoats. I started on some tests boards today on hard maple and really like the results of the water based stain. It minimized the blotching but left enough for a little character. After 2 hours I sprayed my first coat of Endurovar gloss using 1.5mm tip. After 2 hours I lightly sanded with 400 which powdered like a champ. I then sprayed the 2nd coat of gloss.

How do you like to set your spray pattern? Do you turn the needle all the way in and back off X amount of turns? I just tried to eyeball the spray pattern where it wasn't too heavy but enough to wet the surface. My boards looked bumpy after spraying but seem to level out nicely. Here is a few minutes after spraying and you can see the surface. Does this look normal and good coat?

IMAGE_08F149A2-081D-4DE1-AE4A-73B43C0E9E

After 10 minutes it was dry to the touch and looked very smooth. Tomorrow I'll do 2 coats of satin. So far I'm pretty happy with my first attempt.

Looks great. Does the finish dry dead flat after your mid coats? If not and still a little orange peel looking, Spray a littler wetter. The fan I just eyeball. However on fluid, I will count the number of turns. It is important to get a feel for that, it becomes your starting point. My guns seems to be around 2 1/2 turns on the fluid.

-Ace-

  • Author

Ace - do you have an Earlex? I think I can only control the fluid by the knob but not the fan. Do you do 2 1/2 full turns on the fluid?

 

Here is what it looks like after several hours of drying. It feels very smooth to the touch. How do you think it looks after 2 coats of finish? It looks better by eye than the crappy iPhone photo shows.

 

IMAGE_49FC5875-D277-4FDA-BF2B-215908EA6D

No on the Earlex. Try spraying a little wetter. The finish looks just a tish rough. Should dry out glass somooth when you have it right.

I don't use a lot of Enduro Var, I have heard folks say it can be a little quirky to spray. I found, like anything, a little practice with it was needed. Also, the finish is self-sealing so don't spray over shellac or you could have adhesion issues. It's a great topcoat, just reporting what I have experienced and heard folks comment, just takes some finesse.

For grins and giggles, you may want to get a can of General Finishes High Performance and try that or the water-base lacquer. If your new to spraying. Enduro Var is expensive to learn on.

Just my .02 cents

-Ace-

  • Author

I was thinking a little wetter the next coat also. It's for a bathroom project which is why I went with Enduro var over the high performance and I want to practice the same finish as the project will use. Thanks for the tips.

I was thinking a little wetter the next coat also. It's for a bathroom project which is why I went with Enduro var over the high performance and I want to practice the same finish as the project will use. Thanks for the tips.

 

The General Finishes High Performance is "similar"  ;)  to the clear poly used on the professional side which is used for cabinet work.

 

-Ace-

  • Author

Just sprayed the first coat of satin a little wetter and it was level off the gun and is drying very smooth. Had the wet look like Waterlox flowing off a brush. I might dial it back just a hair and try it on a verticle surface and check for runs.

 

Ace - what waterbornes do you like spraying? I went with Enduro-var because off the cross-linkers and amber color. I do want to try the HP and assume it will spray just like the Enduro-var. 

 

Very happy so far with my first attempt spraying AND using waterbornes. I love the look of Waterlox and the ease of use, but get impatient how long it takes to apply on larger projects and the slow dry time. 

How do you like to set your spray pattern? .

You don't. You have vertical horizontal and round no fan adjustment on Earlex. Spray in suggested wet mils to net final dry mils.

Just sprayed the first coat of satin a little wetter and it was level off the gun and is drying very smooth. Had the wet look like Waterlox flowing off a brush. I might dial it back just a hair and try it on a verticle surface and check for runs.

 

Ace - what waterbornes do you like spraying? I went with Enduro-var because off the cross-linkers and amber color. I do want to try the HP and assume it will spray just like the Enduro-var. 

 

Very happy so far with my first attempt spraying AND using waterbornes. I love the look of Waterlox and the ease of use, but get impatient how long it takes to apply on larger projects and the slow dry time. 

 

I like General Finishes and understand their product line. So yep anything General Finishes.

 

Things not requiring a lot of protection, such as clocks, mantles, picture frames...GF water-based lacquer...and is a little cheaper.

 

Tables and really anything else I like the GF water-based High Performance. Last year or the year before, they added corss-linker to the standard mix and made it even better. Previously you had to buy the cross-linker separately and add it.

 

Bar top type things Enduro-Var...But now GF has a new water-based 2 part Conversion Varnish and heard it's really good.

 

High Performance is my favorite!

 

When spraying vertical....give the Enduro-Var a tack coat, meaning spray your first coat on light. Then after it has tacked-up, spray it wet enough, just before it will run, sounds easy right.

 

-Ace-

  • Author

Tables and really anything else I like the GF water-based High Performance. Last year or the year before, they added corss-linker to the standard mix and made it even better. Previously you had to buy the cross-linker separately and add it.

 

Double-checked with GF and the High Performance doesn't have the cross-linker but the Enduro Clear Poly does. Boy, do they have a lot of products!

 

My 2nd coat of satin, one of the edges I didn't get as wet as the rest and it dried slightly uneven but the rest glass smooth. Now that I know what a good wet coat looks like and how it will dry I can look for it when spraying. Those areas I can try hitting again quickly before they start drying. 

 

Good news is it appears any mess-ups can easily be sanded in a few hours and another coat will fix (that is if you don't make the same mistake again).

 

PS - don't keep your bucket of water to clean you gun too close to your drying project (sample boards in this instance). Found out that a splash and couple of water drops landing on your drying boards isn't a good thing... :angry:  Glad I learned that lesson while practicing!

Double-checked with GF and the High Performance doesn't have the
cross-linker but the Enduro Clear Poly does. Boy, do they have a lot of
products!

 

Thats interesting, my contact at General Finishes told me when they stop selling the cross-linker, they were going to add it to the product then increase the price. Remember, Clear Poly is similar to High Performance ;) ;) ;) ;) Perhaps they recently change the recipe?

 

The cross-linker was then marketed towards the 450 exterior line of products.

 

-Ace-

Double-checked with GF and the High Performance doesn't have the

cross-linker but the Enduro Clear Poly does. Boy, do they have a lot of

products!

 

Thats interesting, my contact at General Finishes told me when they stop selling the cross-linker, they were going to add it to the product then increase the price. Remember, Clear Poly is similar to High Performance ;) ;) ;) ;) Perhaps they recently change the recipe?

 

The cross-linker was then marketed towards the 450 exterior line of products.

 

-Ace-

They never stopped selling. They improved the chemical resistance without it so now just claim you dont need it. They still say to use it in the 450 line. It used to be needed for enduro to meet kcma but no longer. Kcma no longer test abrasion but it is still needed to pass old kcma abrasion.

They never stopped selling. They improved the chemical resistance without it so now just claim you dont need it. They still say to use it in the 450 line. It used to be needed for enduro to meet kcma but no longer. Kcma no longer test abrasion but it is still needed to pass old kcma abrasion.

 

My General Finishes contact just advised, yes they did "improved" the clear poly due to the fact cross-linker was becoming too expensive. Had nothing to do with KCMA. Matter of fact, the cross-linker is used in the 450 line-up to make the product cure faster.

 

-Ace-

My General Finishes contact just advised, yes they did "improved" the clear poly due to the fact cross-linker was becoming too expensive. Had nothing to do with KCMA. Matter of fact, the cross-linker is used in the 450 line-up to make the product cure faster.

 

-Ace-

Funny I was just on the phone this morning with my contact, the nice lady that answers the phone. I was asking for advice on using the crosslinker with enduro to finish a jury box with oak benches. She is still suggesting crosslinker on anything that is commercial duty even though the newer formula meets kcma as is. She also stated they suggest it for anything outdoors with the 450 line to make a harder finish.The old formula needed crosslinker to meet kcma.

Funny I was just on the phone this morning with my contact, the nice lady that answers the phone. I was asking for advice on using the crosslinker with enduro to finish a jury box with oak benches. She is still suggesting crosslinker on anything that is commercial duty even though the newer formula meets kcma as is. She also stated they suggest it for anything outdoors with the 450 line to make a harder finish.The old formula needed crosslinker to meet kcma.

 

This really is funny, to whom were you speaking directly to at General Finishes or was this a distributor? Something sounds not right!!!!!

 

-Ace-

  • Author

This is what I was told by Sheryl at GF who has been a great resource at answering all my product questions:

We do make a product called Enduro Poly which is a spray only product, and that is a jumped up High Performance with all those properties on it’s own. The Poly self crosslinks when it starts to dry. You would not add the Crosslinker additive to the Enduro Poly or the Enduro-Var as they already crosslink on their own.

  • Author

BTW, for my needs I think I'm going to stick with Enduro-var to start out. Since I keep my walnut and cherry natural, and color most other woods, the amber that enduro-var gives will be similar the Waterlox that I've always used. If the time comes I need a clear finish then I'll try High Performance. Sure, Enduro-var costs a few bucks more a  quart, but the convenience of one product and added benefits easily outweigh the cost.

 

Of course, the engineer in me always likes to experiment and I'll probably have 6 quarts of other water-based finishes next week to play around with  :D

This is what I was told by Sheryl at GF who has been a great resource at answering all my product questions:

We do make a product called Enduro Poly which is a spray only product, and that is a jumped up High Performance with all those properties on it’s own. The Poly self crosslinks when it starts to dry. You would not add the Crosslinker additive to the Enduro Poly or the Enduro-Var as they already crosslink on their own.

 

I talk and email to Rob Szwedo.

 

-Ace-

BTW, for my needs I think I'm going to stick with Enduro-var to start out. Since I keep my walnut and cherry natural, and color most other woods, the amber that enduro-var gives will be similar the Waterlox that I've always used. If the time comes I need a clear finish then I'll try High Performance. Sure, Enduro-var costs a few bucks more a  quart, but the convenience of one product and added benefits easily outweigh the cost.

 

Of course, the engineer in me always likes to experiment and I'll probably have 6 quarts of other water-based finishes next week to play around with  :D

 

Hey man spray away!  :) :)

 

-Ace-

  • Author

Hey man spray away!  :) :)

 

-Ace-

 

I have been...on test boards!

 

I love Waterlox, but after 2 mission chairs, 3 walnut tables, 3 mission tables, and a nativity cabinet this winter, I'm ready to expand my finishing and try something faster. One coat per day plus an additional 3-4 weeks before I can use it can make one impatient. I'm not looking to dump it but hoping to have more options. 

This really is funny, to whom were you speaking directly to at General Finishes or was this a distributor? Something sounds not right!!!!!

 

-Ace-

Dont know her name just use the 800 number. Just verified again with Johnathan and associates and GF. Both agree with the tech sheets. Johnathan is the west coast sales person for GF. previously ran prelude which IIRC is seal a cell. Enduro is the old an CSS product that was very popular commercially until GF aquired recently reformulated.

From the tech sheet:

General Finishes Enduro Crosslinker may be added if ad-

ditional chemical, water, & abrasion resistance is required.

From GF and Rep

4oz per gallon for performance and enduro 3oz per gallon for 450 clear. Crosslinker $68 per pint.

Dont know her name just use the 800 number. Just verified again with Johnathan and associates and GF. Both agree with the tech sheets. Johnathan is the west coast sales person for GF. previously ran prelude which IIRC is seal a cell. Enduro is the old an CSS product that was very popular commercially until GF aquired recently reformulated.

From the tech sheet:

General Finishes Enduro Crosslinker may be added if ad-

ditional chemical, water, & abrasion resistance is required.

From GF and Rep

4oz per gallon for performance and enduro 3oz per gallon for 450 clear. Crosslinker $68 per pint.

 

I just heard from Rob at General Finishes....he said the cross-linker is still on the market but only for the 450 product line to speed the cure (as I indicated in an older post) . Adding cross-linker to the Clear-Poly will make the product to thick (before with the old formula, it didn't) and is too expensive to do what it does to the Poly. Soon the cross-linker will be discontinued.

 

Also, the tech data sheet's on their web-site are in need of updating. Finally, Rob advised me, should you have any further questions or concerns, call him directly, again his name is Rob Szwedo of General Finishes. His telephone number is 800-783-6050.

 

I hope this helps you Don?

  • Author

So Ace, after your research does this information match what you learned? :)

 

High Performance - no cross-linker

Enduro Clear Poly - has cross-linker

Enduro-var - has cross-linker

So Ace, after your research does this information match what you learned? :)

 

High Performance - no cross-linker

Enduro Clear Poly - has cross-linker

Enduro-var - has cross-linker

 

Ok here is what General Finishes has to say about High Performance...Winner of Fine Woodworking's Best Overall Choice Award, High Performance

Top Coat is the hardest, most durable consumer polyurethane top coat on the market today. It contains all the consumer friendly characteristics of PolyAcrylic Blend.

 

It's like asking Colonel Sanders what is the secret recipe to his chicken is? They won't say for sure! Thats why the word "similar" is used. I wonder if General Finishes just adds something to the Clear Poly that is already cross-linked to make it brush-able (sorta like deft adding retarder to the solvent lacquer to make it brush-able???)   Or hell... is it just the same product re-marketed for the retail side??????? Only General Finishes knows for sure...and I don't blame them!!!!

 

-Ace-

  • Author

I'm not quite sure what information you are trying to get from GF, but all I really care about is what products give me the best protection in a bathroom. The lady clearly said that High Performance doesn't have cross-linker but Enduro-var and Enduro Poly do. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.