Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

help with a mistake?

Featured Replies

Hey all,

 

I've been working on the roubo for quite a few months now and I'm just starting on the leg vise.

 

Here is my problem.  I mistakenly have already drawbored the front left and back left legs together.  I have yet to make any mortises or drill any holes in the front left leg for the vise. 

 

The way I see it now is that I can make the through mortise for the parallel guide from the one side, no problem.  I have a long enough bit.  I can also drill the hole for the vise screw and make the mortise for the acetal plate without issue.  My main concern is that there is no way I would be able to make a mortise for the nut plate (the nut for the giant vise screw) on the back side of the leg. 

 

How essential is it to have that round nut plate mortised into the leg?  Can I just use screws to hold it in place on the surface?  Because, its either - surface mount the nut plate on the back OR drill out the draw bore pegs.

 

Which do you guys suggest?

 

 

I would suggest drilling out the pegs.  Not because you have to mortise for the nut...you don't (although it's certainly preferable).  But because you want to be as precise as possible with your drilling for the vise screw, mortise for the acetal plate, and mortise for the guide.  I'm sure it can be done, but the extra amount of effort and the risk of screwing it up...to me, it'd be much less work and will allow for much greater accuracy if you just drill out those pegs.  Fixing drilled out pegs is easy-peasy...drilling the vise screw hole and through mortise for the parallel guide...accurately...freehand?  Not so much.  Get that bad boy on the drill press and do 'er up right. :)

  • Author

Thanks for your input. Its the way I've been leaning.

As far as drilling out the pegs, is there any specific best way to do it? Should I use the exact same diameter to drill them out?

I'm also guessing that it ruins the drawing in effect by making the new holes perfectly aligned. Any trick to prevent that? Or shouldn't that matter too much?

I think I'd start with a smaller diameter bit than the pegs and try to bore out most of it, then *attempt* to pull out the remainder with a little chisel, needle nose pliers, whatever.  This way you don't change the diameter of the holes...but this will be tough since it's all end grain and your bit will want to wander.

 

If that doesn't work, I'd just use the smallest bit you can to adequately excavate all the peg material.  Take your legs and stretchers apart.  Then, personally, I'd plug those holes back up with glued in dowels that fit TIGHT.  Let them dry, saw and sand them flush, then start the whole drawbore process again in the same locations.  OR, if you have enough space left on your tenons, you can plug the holes back up then put the pegs in new locations.  OR you can just use bigger dowels, if things not matching doesn't bother you.  It would drive me nuts every time I saw them, but that's just me.

 

Marc should chime in on this eventually.  If you're a Guild member you can email him directly...I'm sure he's got a better idea that I've never thought of.

I think drilling out with the same sized bit, take it part and then drill and plug the tenon with a larger dowel, then re-draw bore would be the simplest way to go. If the plug is a tight fit, it will work as well as the original effort. I am assuming you didn't glue the tenon as well as draw bore. If you did, then I dion't think it's a big deal to not mortise the big nut. It will hold and after a year I have yet to have anyone look at the back of the leg to see how the vise is held in place.

  • Author

Thanks for the input everyone. 

I was about to start drilling out the pegs and getting back to work, when I had an idea.

 

I've modified my drill press a bit, and set it up on somewhat of a custom "stand" and I have been able to drill all the holes with the two legs still attached.  I was originally worried about not being able to use the drill press since the two were stuck together and the whole thing was too big.  Since this is no longer an issue, the only thing I'm left with is the mortise for the big nut on the back.  Now, I'm starting to think I will just attach it to the surface of the leg with lag screws for strength, instead of drilling and tapping.

 

I'll let you know how it turned out. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.