Recommended Posts

Posted

I have searched the forum, and scoured the Internet, but still need some help a few points on the domino. I watched Paul Marcel's podcasts, which were quite informative.

I am pretty sure the 500 model will suit my needs well. I mostly build with 3/4 to 6/4 hardwood stock, occasionally using 8/4. I understand the 500 comes with a 5mm cutter, which does not not seem sufficient. I probably should buy the cutter kit.

I really wanted a tenon sizing chart, and I read the manual and supplementary manual, and all it stated was the typical "one third the thickness" as a guideline.

So what it really boils down to, is how long and which mm tenons can the 500 cut, and are they suitable for my work. So maybe you experienced festool domino users can respond for me:

Hardwood

If I were joining a 1 1/2", 3/4 stile to a 1 1/2" 3/4 rail (as in a face frame), which would I use?

If I were joining a 2 1/2", 3/4 apron to a 6/4 leg, which would I use?

If I were joining a 3", 7/8 apron to an 8/4 leg, which would I use?

Plywood

How about standard hardwood ply to standard hardwood ply, like constructing a box or placing shelving?

Posted

5 or 6mm dominos will do almost every 5/8 to 7/8 thick material joinery. For 8/4 to 8/4 joints you can use a bigger tenon or use 2 5mm stacked 5 mm apart in the center.

I used the 8mm tenons in the corners of a large frame and panel door that I built from 5/4 oak. We made our own tenon stock to fit the wider settings on the domino and cut the length to use the maximum depth settings.

Rip, plane and round the corners on the router table. It is not that hard to make your own domino tenon stock in any size or wood you might need. Be careful and accurate, use a dial caliper to insure a good fit.

If you are doing a lot of 1/2" or 3/4" sheet goods case joints I recommend the Domiplate aftermarket accessory . It mounts to the bottom of the machine and does produce corners that are flush and very square. If you have used a biscuit machine you know that unless you are very careful the joint may not be perfectly flush.

We bought the 4mm bit to join the corners on 1/2 Baltic birch drawers. You have to watch the depth settings when you are plunging into the face of a board. Cutting all the way through kinda ruins the part.

You must have a vac hooked to the Domino to use it! I used mine for years with a Fein vac. I added 3 "o" rings to the dust port to improve the hose fit. Now that I have a Festool CT 26 it is a bit more convenient but either way worked just" Fein" ( grin)

I just bought the bits as I had a need for a different size. Still don't have a 10 mm bit yet.

  • Like 1
Posted

==> If you are doing a lot of 1/2" or 3/4" sheet goods case joints I recommend the Domiplate aftermarket accessory

 

+1 on the domiplate.

Posted

Even the 3" by 7/8 to 8/4 joint is limited by the 7/8 material, a 6mm or 8 mm tenon is plenty. When a joint is too narrow for 2 dominos and you want something wider than the stock tenons the wider slot settings and homemade tenons are the solution.

Posted

I mostly use woods of the dimensions you list and the 500 is all I've ever needed.  I've had mine since it was introduced in the US and consider it one of the most useful tools in my shop.   Another couple third party add-ons some may be interested in are at   http://www.dominoguide.com    An excellent in-depth guide for the Domino can be found here  http://www.waterfront-woods.com/festool/   

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 49 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined