Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Mini Tour of my Basement Shop

Featured Replies

My shop area is a (roughly) 18' X 25' area of my basement.

 

That statement alone doesn't sound too bad....but the basement is short....really short. I am 6'-1" tall. The floor joists are about 6'-4" above the floor, and there's 2 beams that run the length of the basement that are 5'-9" above the floor. There has not been a single time that I have gone down to the shop without thumping my head on one of those beams! There's also quite a few posts that are supporting the beams, and they do inhibit me from rearranging my shop layout. I have my tablesaw it the only place it can possibly be, and I just try to create a flow around that. It can be a PITA, but most of my tools are on wheels.

 

Here's a picture of my Mitre saw station that shows the beams and posts.

post-13786-0-28137600-1366688334_thumb.j

 

Here's the Porter Cable Tablesaw. It's my first tablesaw purchase, and it's worked well for me so far...no real major complaints, and I love the mobile base.

post-13786-0-74789900-1366688521_thumb.j

 

And this is my quick and dirty router/assembly/outfeed table. the top is 2' X 4' and it's mounted on strap hinges (to make depth adjustments without getting down on the floor). Even though there are no wheels, it is light and small enough to drag wherever it's needed.

post-13786-0-29247600-1366688776_thumb.j

 

 

 

The basement shop is far from ideal, but it sure beats having no shop at all....or having to borrow a friends shop.

 

I do have a single car detached garage that I use for larger project assemblies and some fininshing occasionally, but that's about it. No power and no insulation have kept me from setting up a 2nd shop....so far.

 

 

Looks like You have set it up well with the space You have. In My Garage a low hanging heater finds my head a lot, so I padded it with foam pipe insulation, maybe a idea for Your beams. 

Great shop Daniel. I think small shops are great, they force you to be really creative to make the best of the space. You can't just fill it with non essential tools either, only the important stuff finds a home. 

Daniel....I really want to do Tosh.0 take aways. :) 

I have the similar problem --not as low as yours but I like to hang things from my joists.  I try to concentrate on hanging things over tools and tables - where I'm NOT walking.... other times I just wear my hardhat in the shop....and put on my tool belt and and sing YMCA.

Seriously....this could work....lay the shop out and figure where you'll be walking...until Jesus comes.  Your joists are probably 2x8s or 2x10s.  You're going to trim a few inches of each joist away in a 3' path (assuming you're walking perpendicular to the joists. You could use a 3 or 4 foot 2x4 and lay it beside the joist up against the floor.  Glue and lag screw it to the joist (Scab it) then trim the joist some in the walking area so the joist(s) are normally 2x8 and 6'4" high but in the 3' wide path where you'll walk, the 2x8 becomes a 4x4 and it's 6'8" high but just for 3 foot "path".  I'd probably do it with 4' pieces of 1/4 x 4 flat bar and lag screws but wood would work too - glued and screwed. Now, I hear the engineering types murmuring some so I'll say CONSULT AN ENGINEER. There I've said it....but I think something like that would work in limited areas without the house caving in. Like in a plant, paint lines on the floor to marking a path that corresponds with the cut outs and you're gold.....or just wear flip flops, a hard hat, sun glasses and .....SING BROTHER.........SING!!!

  • Author

Looks like You have set it up well with the space You have. In My Garage a low hanging heater finds my head a lot, so I padded it with foam pipe insulation, maybe a idea for Your beams. 

 

Sounds silly.....but I'd never even considered padding the beams. I guess I figured that I would just learn to duck where I need to!

 

 

 

Great shop Daniel. I think small shops are great, they force you to be really creative to make the best of the space. You can't just fill it with non essential tools either, only the important stuff finds a home. 

 

You're right about that! Non essential tools...and some floor-type tools just will not work in my shop. I tend to use mostly bench model machines...and some hand tools.

 

 

Daniel....I really want to do Tosh.0 take aways. :)

I have the similar problem --not as low as yours but I like to hang things from my joists.  I try to concentrate on hanging things over tools and tables - where I'm NOT walking.... other times I just wear my hardhat in the shop....and put on my tool belt and and sing YMCA.

Seriously....this could work....lay the shop out and figure where you'll be walking...until Jesus comes.  Your joists are probably 2x8s or 2x10s.  You're going to trim a few inches of each joist away in a 3' path (assuming you're walking perpendicular to the joists. You could use a 3 or 4 foot 2x4 and lay it beside the joist up against the floor.  Glue and lag screw it to the joist (Scab it) then trim the joist some in the walking area so the joist(s) are normally 2x8 and 6'4" high but in the 3' wide path where you'll walk, the 2x8 becomes a 4x4 and it's 6'8" high but just for 3 foot "path".  I'd probably do it with 4' pieces of 1/4 x 4 flat bar and lag screws but wood would work too - glued and screwed. Now, I hear the engineering types murmuring some so I'll say CONSULT AN ENGINEER. There I've said it....but I think something like that would work in limited areas without the house caving in. Like in a plant, paint lines on the floor to marking a path that corresponds with the cut outs and you're gold.....or just wear flip flops, a hard hat, sun glasses and .....SING BROTHER.........SING!!!

 

Sounds kind of like a tunnel system...A GIANT HOBBIT WORKS HERE!

But seriously...I don't plan to touch any of those joists or beams. It's a rental house, and I can see evidence of past fire and water damage. On section of the beam looks like someone took an ax to it once. All the joists seem to be modified already and I'm just not sure how much more they would take. It looks like something that would really make Holmes on DIY angry.

I was going to suggest the foam pipe insulation too but got beat to it.  It doesn't stop a good thump from hurting but it does take away some of the sting.  Don't need to ask me how I know.

Very nice. I'm currently of the mind that almost ANY dedicated space is a better shop option than shared space, so enjoy not having to spend half your shop time wheeling tools into position and back when you're done. :) 

 

Over time, I'm guessing you'll figure out all kinds of storage ideas as you work in it, increasing the usable space.

 

It's oriented around metalwork and auto repair, but if you've ever checked out the 12 gauge garage  - http://12-gaugegarage.com/ - I like how he has all kinds of fold down work surfaces, and a lot of thought into where tools are, and where you can find extra storage space. 

 

And it's a damn cool garage too.

 

Enjoy the shop!

  • Author

That is one CLEAN looking shop. Lots of cabinets too.

 

Storage solutions is something I have been considering recently. I don't have any cabinets. I have some pegboard and a lot of shelves. The quirky little philosophy of mine is that it will take longer to find something if I have to open doors and drawers to search for it....and my organizational methods are pretty loose. Not every tool has specific location, but they all have a general area. Every time I start a new (big) project, the whole shop gets cleaned and organized. Start with a clean shop and a clear mind (that's good advise for anybody!)....but I find myself putting off projects more and more because I do not look forward to cleaning day. It's just not fun work, and I find myself getting sidetracked by tinkering with my shop layout.  

 

I don't want to make it sound like it's a total mess...I know where my stuff is (generally). I might have to dig upsome old pictures of my Dad's machine shop and my Granpda's too. The mess in those shops was glorious!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.