Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Bed repair

Featured Replies

I have a bed I need to repair. The headboard is attached to the side rail by a bed bolt with a half moon. The wood inside the headboard has cracked a bit under the washer and I am concerned about tightening the bolt more due to potential splitting of the wood. The washer is somewhat bent. I am wondering what my best course of action would be. I thought about using an epoxy to fill the area(after inserting a sleeve to keep the hole for the bolt open) or maybe drilling down a bit and inserting a wooden dowel and drilling back thru from the side rail end. My expertise is at a low level and I would rather go the epoxy route but I am concerned about the strength of the epoxy in respect to the amount of pressure exerted by tightening the bolt. Thanks in advance for any and all help.

  • Author

As you can see in the picture the washer has broken thru an outer ring. The inner channel for the bolt is about 3/4 of an inch behind it. I was thinking I could clean out the outer ring and glue in a hardwood dowel pin unless someone has a better idea. Thanks

Why is it a half moon? I think of half moons for joining in a parallel plane with an embedded stud, half moon, nut arrangement. The through hole bored showing in your pic appears off-centered. Is this why there is a half moon?

  • Author

The picture is the head board. The bolt is pushed thru here and attaches to a half moon in the side board of the bed. There was a complete circle of wood where the washer abuts  ( I would think) at one time.

I would find a dowel or smooth rod to keep the hole clear and lube it with grease or Vaseline . Then glue a new metal washer into the hole with some epoxy putty. The thick paste that you knead until the color is blended.

  • Author

I would find a dowel or smooth rod to keep the hole clear and lube it with grease or Vaseline . Then glue a new metal washer into the hole with some epoxy putty. The thick paste that you knead until the color is blended.

Not quite clear on what you suggest.

Two part paste epoxy products are a great large gap filler.  They make varieties that are resistant to gasoline and can be used to patch active leaks in automobile gas tanks. They work, I know from personal experience, and outlast the metal of the gas tank as it rusts.  I am not sure if all such products are compatible with wood as a binding agent but the epoxy would mold to the irregular broken surface of the bottom of your round mortise and could provide a flat surface which would keep your washer from bending and crushing the wood fibers unevenly.  In the situation he describes, you use the walls of the mortise as a sort of form as if you were pouring the hole full of concrete.  The lubed dowel would be run through the bolt hole and left sticking way out on both sides to keep a through hole so that you will not have to drill through the epoxy.  This could also align a washer so that you can push the washer into the epoxy while it is fresh and ensure you get a flat seat between the epoxy and washer.  A picture is worth a thousand, but I couldn't find one appropriate.

  • Author

That makes sense. If I were to tighten the bolt would it crack the epoxy? I was thinking of using some JB Weld but did not know its strength.

I don't think you'll blow the back out with even pressure all around but without my fingers on the wood it is hard to say. Most putty epoxy cures as hard as wood or harder. Some are used to embed structural steel in concrete. The one thing I cannot do without research is suggest a brand or type.

The epoxy paste I have used for years is PC-7. They had a display of a soda bottle glued to a wood base with a wood shelf on the side, metal hooks glued to the bottle and a golf ball on top. That stuff will stick to anything.

  • Author

Used my dremel to clean out the hole. Used a number of metal washers. Works like a charm.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.