Kranzpj Posted May 9, 2013 Report Posted May 9, 2013 I recently purchased my first jointer, a 6" Grizzly, and I'm having a problem getting dead flat cuts. When 2 jointed faces are put together I'm getting a concave curve of about a 32nd over 24". Setup - Outfeed and infeed tables are flat and seem coplaner. The outfeed table is set high enough that a straight edge moves 5/32" toward the infeed table when the cutterhead pulley is rotated (as per the manual). I've tried a little higher and a little lower and have gotten similar concave results. I have not reset the knives. I want to avoid that if possible. Technique - I've been putting pressure on the infeed side until about 6" of the board is over the cutterhead then transfering the pressure to the outfeed table. I did notice that on thinner boards I was putting so much pressure down that I was actually flattening out the concave curve and making things worse. After lightening up the results were better but still detectable. Any ideas? -Paul Quote
EdgewaterWW Posted May 9, 2013 Report Posted May 9, 2013 I have not setup a Jointer, so no hands-on help that I can give. But have You looked at Marc video? 118 Jointer setup or maybe it's time to call Grizzly Support. Good Luck 1 Quote
dwacker Posted May 9, 2013 Report Posted May 9, 2013 To much pressure. Outfeed tilted down Bed to short. Most common is to much pressure and bed to short. 1 Quote
mikem Posted May 9, 2013 Report Posted May 9, 2013 I had this problem on my Delta bench top jointer, frequently caused by the beds being too short. I put a roller pin stand off the outfeed bed, which went a long way in helping. The setup is touchy at best as you need to get the stand as close to the same height as the outfeed table as possible. 1 Quote
Kranzpj Posted May 9, 2013 Author Report Posted May 9, 2013 Thanks guys. The bed is 46" (http://www.grizzly.com/products/6-x-46-Jointer/G0654) so hopefully that's not the problem. I'll try less pressure and try to see if the outfeed table is tilted. Quote
dwacker Posted May 9, 2013 Report Posted May 9, 2013 Thanks guys. The bed is 46" (http://www.grizzly.com/products/6-x-46-Jointer/G0654) so hopefully that's not the problem. I'll try less pressure and try to see if the outfeed table is tilted. That would be short for a jointer. Joint a 20" board to check the outfeed. Quote
jmaichel Posted May 9, 2013 Report Posted May 9, 2013 Paul, You and I probably have the same jointer. I just finished setting it up a few days ago and am not having any problems. Make sure the front of the outfeed table by the cutter head is coplaner with infeed table. Mine wasn't so I shimmed the outfeed table with .002 shims and that got me to .004, which is close enough for me. Quote
CessnaPilotBarry Posted May 9, 2013 Report Posted May 9, 2013 Just a thought... Lots of people TRY to get edges to be glued up slightly convex, rather than perfectly straight. It's called a "spring joint", and is intended to help keep the ends of the glued up boards tight over many years. Maybe you're a natural! 1 Quote
Kranzpj Posted May 10, 2013 Author Report Posted May 10, 2013 Paul, You and I probably have the same jointer. I just finished setting it up a few days ago and am not having any problems. Make sure the front of the outfeed table by the cutter head is coplaner with infeed table. Mine wasn't so I shimmed the outfeed table with .002 shims and that got me to .004, which is close enough for me. What did you shim it with? Quote
jmaichel Posted May 12, 2013 Report Posted May 12, 2013 What did you shim it with? I used a cheap set of feeler gauges, cut them up and used them as shims. Quote
Trip Posted May 12, 2013 Report Posted May 12, 2013 ==> I used a cheap set of feeler gauges, cut them up and used them as shims. creative -- i'd never thought of that... you can also get shim stock at mcmaster-carr. i got a small set of brass/ss shim stock for like $29 from mcmaster about 15 years ago, and have been using it ever since. Quote
Mike Frank Posted May 12, 2013 Report Posted May 12, 2013 save your money use old pop beer cans you can stack them cut in thin strips been done for years thought everybody knew that Quote
Trip Posted May 12, 2013 Report Posted May 12, 2013 ==> old pop beer cans you can stack them cut in thin strips been done for years thought everybody knew that missed that class.... creative, but i'll stick to shim stock... Quote
jmaichel Posted May 12, 2013 Report Posted May 12, 2013 I looked for shim stock and did not want to order it. The next best thing was to buy a $6 feeler gauge set and use that. Mike, I have heard of using soda or beer cans and considered it but ended up just using feeler gauges. Quote
Trip Posted May 12, 2013 Report Posted May 12, 2013 ==> The next best thing was to buy a $6 feeler gauge set and use that. it's really a good idea... if i didn't have a supply of shim stock, that's the way i'd go. Quote
Don Z. Posted May 13, 2013 Report Posted May 13, 2013 ==> old pop beer cans you can stack them cut in thin strips been done for years thought everybody knew that missed that class.... creative, but i'll stick to shim stock... Someone hasn't read Zen and the Art of Motorcycle Maintenance... Quote
Kranzpj Posted May 13, 2013 Author Report Posted May 13, 2013 I used a cheap set of feeler gauges, cut them up and used them as shims. How did you get the shims in? I loosened the gibs which I thought would increase the play in the table, but it didn't. Quote
Trip Posted May 13, 2013 Report Posted May 13, 2013 ==> Someone hasn't read Zen and the Art of Motorcycle Maintenance... I read Zen in the Art of Archery at uni, but Motorcycles weren't on the syllabus... With the feeler gauge tip, obviously there were gaps in my education... I'll get a copy... Quote
jmaichel Posted May 13, 2013 Report Posted May 13, 2013 How did you get the shims in? I loosened the gibs which I thought would increase the play in the table, but it didn't. Make sure you loosen both gibs almost all the way on the outfeed table. Then push up slightly underneath the back of the outfeed table and slide the shims into dovetail way on the outfeed table. It's hard to explain, if I was at home I would able to take a couple of pictures and it may make more sense. Quote
Trip Posted May 13, 2013 Report Posted May 13, 2013 ==> Make sure you loosen both gibs almost all the way on the outfeed table. Then push up slightly underneath the back of the outfeed table and slide the shims into dovetail way on the outfeed table. also, sometimes there is baked-in-crud (usually sawdust + oil) preventing table movement -- if you have shop air, you can blow-out the crud... Quote
CessnaPilotBarry Posted May 13, 2013 Report Posted May 13, 2013 Most hobby shops, and some craft stores, sell brass shim stock in small quantities in the K&S Metal display. For a few bucks, there's an assortment that includes a sheets of varying thicknesses, ~ 3" x 5" in size. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.