Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

I think I've decided on a lumber rack design

Featured Replies

In the idea of keeping things non-permanent and easy to remove without leaving behind much damage, I came up with this design for a lumber rack:

 

67759957-62C7-4305-9480-1E9142C51F32-461

 

Allow me to explain. I am in a basement, and I don't want to drill holes into the cinderblock walls. Just a personal preference that I am sticking with. I wanted to keep a lumber rack off the ground and as vertical as possible. I didn't want all this weight supported just from one concentrated area of a floor joist. Again, a personal preference.

 

The red is the cinderblock wall, the left-most green stud is a 2x12 sitting on the cinderblock wall. The remaining floor joists are 2x10's. On this particular wall, the joists are parallel to the cinderblocks, and the last row is just outside the edge.

 

The purple part is how the rack will fit into the space. I will have to notch about 1/4" off the face of each 2x4 on the rack to fit the gap, but that is ok. That is not where the support comes from. A block with a piece of metal as a gusset on both sides will be attached to the vertical 2x4 for the rack, and all the downward pressure will be here. The joist keeps the rack from falling off the wall, and the weight of the lumber on the rack gives the rotational force required to keep it firm against the wall - without fasteners.

 

I figure I could run the entire 15ft wall like this if I wanted to, and they stay modular because they are not fastened in place! One vertical member every 3-4ft should be plenty strong.

 

Any suggestions?

Seems ok p as long as the load is minimal. If the loads are a bit on the heavy side you could run the wall stud all the way down to the floor. A least the load would then be into the floor rather than just relying on it hanging. An angle bracket into the floor/stud would then keep it strong and not flapping about so to speak.

I would brace the under side of your floor joists and potentially block between them. The bottom of a joist can move a bit and I would seek to eliminate that motion.

  • Author

Seems ok p as long as the load is minimal. If the loads are a bit on the heavy side you could run the wall stud all the way down to the floor. A least the load would then be into the floor rather than just relying on it hanging. An angle bracket into the floor/stud would then keep it strong and not flapping about so to speak.

I was thinking about screwing the vertical member into the floor joist, as well. Going down to the floor is a good idea, and I will probably do that as well.

+1 into the joist too, last thing we want is a disaster.

 

C has a good point to some extra strutting, solid or herring bone would limit deflection for that belt and braces approach.

  • Author

I don't think the floor joist risks any chance of deflection. All the force holding the rack is downward and placed on the cinderblock wall. The floor joist is only there to make sure the rack does not fall off the cinderblocks. I only intend to screw into the joist to fix the vertical members laterally along the wall.

I'd put a screw adjustable foot on the bottom of each vertical member, and adjust it so that it was just touching the floor.  If the load causes any stretching or deflection, the foot will start to share the load with the concrete block wall.  And, the metal foot won't wick moisture into your wooden member, which would be a problem if the wooden vertical piece went down to the floor.

I see downward force at the outside of your shelves creating inward pressure at the bottom of your riser and outward pressure at the top. Every little bit that your purple separates from your block wall creates more weakness in the bearing joint at the top of your block wall. You know how much load you need to carry better than I but I see a very small investment eliminating the thought from your mind for good.

  • Author

I see downward force at the outside of your shelves creating inward pressure at the bottom of your riser and outward pressure at the top. Every little bit that your purple separates from your block wall creates more weakness in the bearing joint at the top of your block wall. You know how much load you need to carry better than I but I see a very small investment eliminating the thought from your mind for good.

Yeah, I see where you're coming from. The joists have those boards that form an X. But, I'm not sure how far the closest one is from where I want the rack. I will have to look when I get back home. Will those suffice if close enough?
  • Author

They should. That X shaped design out of wood or metal provides the bridging I would look for.

If they are close enough, I will rely on those. If not, I will just add more of them.

Thanks for the suggestion.

How long are the boards that you will be storing? If you have the ceiling height, creating a rack to store your boards vertically is really easy, and you don't have to worry about how strong the rack is since each board is ultimately supported by the floor. In addition, it's easy to get to your wood because you can page through the boards sort of like pages in a book, as opposed to trying to get that one board you want that is under a stack of 8 other boards. 

 

Here's mine. The platform is 2x4's screwed together as a frame, with 3/4" plywood on top, and some scrap pieces of wood that serve as a stop to help keep the boards from sliding back and forth too much. The platform just rests on the ground, as the weight of the wood holds it in place. The metal rods are pipe that are screwed into fixtures (all available at Home Depot) that are attached to the board that is on the wall. 

 

tumblr_ll0fuhCCqJ1qb9n9qo2_1280.jpg

 

This is what it looks like fully loaded. This takes up a lot less floor space than this wood did when it was lying flat.

 

tumblr_ll0fuhCCqJ1qb9n9qo4_1280.jpg

  • Author

I like the idea, but I don't think it would fit me too well. I would like to have the floor space open underneath the rack. I also will use the design to hang some sheets of plywood from the wall to use as tool storage. Possibly even small shelves/cabinets.

  • 4 weeks later...
  • Author

Not finished, but this is a rough start just to get my lumber organized and away from where it was previously. $8 for 2x4s and the plywood for the gussets was leftover from the crate that my jointer came in. I will later modify the whole design, but this works for me for now.

 

Don't mind the small mess accumulated on the floor under the lumber rack  :blink:

 

F9D24B79-88EB-4FDA-92D6-5B098A72D9C3-672

  • Author

Looks like someone has been working on the http://www.youtube.com/watch?v=T9IZDInBv1M!

HAHA.

I plan on making another vertical support so I can somewhat separate by size and species. I am going to start buying a good supply of maple. Plan on starting a bench in the future.

Wilbur great rack. +1 on storing wood vertically, for all the reasons stated. I'm planning something similar in the near future.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.