Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Movement after milling and storing

Featured Replies

Hi all, apologies if there's an answer to this and I just haven't found it! I'm new to the site and only have 6 projects under my belt. I understand that many woodworkers mill wood to rough dimensions and leave it a few days before milling to final dimensions. I have a couple of questions on this process:

1. How close to final dimensions should the first milling be? Forgive me if the answer is how long is a piece of string, just looking for some rough guidance.

2. Like many my workshop is my garage (the car goes in there too) after milling should I store the wood indoors or can I keep it in the garage?

For 2 I've tried both but haven't tried 1 yet. I'm keen to minimise movement on my next project as I've had some movement in all my projects.

Thanks in advance.

I can't really give bonafide advice, but I can tell you what I do any why I do it.

 

My basement is my shop. When I buy lumber, I bring it home and let it sit for 4-5 days. I think skim it across the jointer on all four sides just to get some of the wood underneath showing. I maybe take around 1/8" or less off the board in total thickness and width. I do this to allow the wood to "breath" a little more. Is there science to back this up, probably not. I've never looked it up. I just like doing it.

 

After the wood sits for another 4-5 days, I mill about the same off the large sides, not the edges. After that, I let it sit for 1-2 more days, and do whatever I want with it then.

 

If you are in your garage, I wouldn't really try too hard to keep it inside. What are you going to do when you are in the middle of a glue up that you have to leave over night in the garage? It's inevitable, you will have to leave your projects in the most of the time. How well is the garage insulated, and what are the chances of using a dehumidifier?

 

Again, not really advice, more so just my process.

Question 1, I haven't actually done, but I would think just enough to get a square flat board.  When you are ready, take it down the rest.  Another option, which is what I have done on my current project, is only mill what you need for the current phase of the project, and try to get a glue up as soon as possible, the same day if possible.

 

For question 2, I would leave it in the garage.  The change in environment could potentially cause more movement.

I wouldnt worry about it unless there is a question of moisture content or your milling big chunks into much smaller chunks.  If your milling 4/4 into smaller 4/4 then it should not matter. Cutting something like 12/4 into 4/4  its probably a good idea.

Hi Darren,

 

As a general rule I add 6mm to my finished sizes (100 x 100 finished would start as 106 x 106 sawn) to allow for preparation. If it's something more tricky or I suspect I might have problems with it (Iroko) I add a a few more mm to be safe. On the flip side if the wood is a bit mean I will try for less if I think I can trust the wood.

 

As long as the garage is reasonably dry a day for some tension to release and the wood to settle would be fine. Taking it indoors can work, but you are going to need  to take it into the garage to work the timber anyway. Embrace the potential for movement and make allowances for it where you can. With the weather we have at the moment you garage should be super dry  ;)

Be sure to remove equal amounts off both faces, and sticker and stack everything flat so air flow can get to both sides of the boards.  And make sure all your stickers are of equal thickness, otherwise you can introduce bowing or twist.  I only mill more than once when I'm taking off an 1/8" or more from both sides.

+1 on Grahams and Erics notes. I always leave the wood in the shop after initial milling as it can then be exposed to the humidity/temperature in there and when milling do both sides of a board, alternating when pushing through the planer, to make sure you expose both sides equally. This will eliminate unequal exposure of fresh wood to the air and therefore minimise twist/cupping etc. Beware though that wood can also do its own thing and sometimes boards just want to twist/cup and is just par for the course.

  • Author

All, thanks for the advice. I checked the moisture content on some of the American white oak I have had in the garage for over 12 months, got readings between 8 and 11%. Assuming my meter is reasonably accurate the wood stacked on shelves is dryer than that leaning against the wall.

Going to go with leaving it in the garage, will make life easier as well.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.