Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Spraying water based topcoats indoors

Featured Replies

As I stated in other posts, I am new to spray finishing and am currrently spraying my first project. It's going well, but I am reliant on the weather being nice to get it done as I am spraying outdoors.

I did a quick google image search for indoor spray booths, and got some general ideas. Do any of you guys have a spray set up in your shop? If so, can you discuss, post a pic, or offer some general advice?

I will only be spraying water based materials. If I decide to spray solvent, it will certainly be outdoors.

Most will not agree with this but its actually easier to spray solvent in your shop. With water you need to cover near by equipment. Water does not dry fast enough so it lands on your tools wet and sticks. With solvent you can spray a few feet away from equipment and the overspray will be dry before it ever hits the machines. If you have a roll up door you can add a row of fans pointed outside and it will exhaust some of the fumes. I spray solvent daily dont cover anything except the jointer because I spray a foot away from it.

 

You can filter with your fans but do NOT buy those pleated filters the fans dont have enough HP. This is one of my filters after a day of spraying lacquer. Remember with any finish you still need a respirator.

 

 

 

 

Most will not agree with this but its actually easier to spray solvent in your shop. With water you need to cover near by equipment. Water does not dry fast enough so it lands on your tools wet and sticks. With solvent you can spray a few feet away from equipment and the overspray will be dry before it ever hits the machines. If you have a roll up door you can add a row of fans pointed outside and it will exhaust some of the fumes. I spray solvent daily dont cover anything except the jointer because I spray a foot away from it.

 

You can filter with your fans but do NOT buy those pleated filters the fans dont have enough HP. This is one of my filters after a day of spraying lacquer. Remember with any finish you still need a respirator.

 

attachicon.gifphoto-6.JPG

 

attachicon.gifpost-5350-0-56584900-1377090659.jpg

What type of fans do you use?

IMG9999.jpg

 

This is a downdraft table I made and use in my basement shop (for smallish projects) . I use a 3 speed heating and cooling fan and stack 2 20x20 furnace filters. 1 of the filters is a cheaper one and use as a "pre" filter and place good pleated one stacked last.

 

Easy to build, you enclose the fan motor in a plywood box inside the table and exhaust out the side of the table, then cut a square hole out one side of the box as the air intake and filter stack. I use only for water-based. Large projects get sprayed out in my garage.

 

In the basement, I will hang old bedsheets around the downdraft table to contain overspray. Funny story....this started out as a down draft sanding table and you know the rest. Hehehehe.

 

-Ace-

  • Author

I was thinking maybe something like this. Is this a good idea?

http://www.finewoodworking.com/how-to/article/make-a-simple-spray-booth.aspx

Or

I have room in my basement for a dedicated spray booth. The issue is the only ventilation is from those typical small basement windows. I could frame out a small room, use 6 mil poly stapled to the studs, and use a zipper door for access. The fan could blowout the window, and I could install a make up air vent opposite the window. Most of the work would be well below the window however, so this may not be a great idea.

I think this is great. I would suggest a strong fan that can move air. Take a trip to your local heating and cooling business. And purchase a used furnace fan for about $45.

Maybe some flex hose to duct the exhaust out the basement window.

-Ace-

When spraying in the house. I turn off my furnace so not to pull any overspray into it. Also run my overhead air cleaner to help clear the room. Really not a big issue on smaller projects.

+1 for using a furnace blower. For spraying you might consider a plywood chase so the fan draws air at the table level. Some ribs and Luan is all it would really take.

franklin - I've built that booth but have yet to use it. There are more detailed plans in Jeff's book. His book and DVD are great resources for anyone starting out with spray finishing. I used 1.5" pink foam for the booth and it collapses flat at 6" thick. If you do decide to built it let me know as I made a few simple changes. There is also a plan for a rotating spray table which I have the parts but haven't built yet. 

 

http://www.amazon.com/Spray-Finishing-Simple-Step---Step/dp/1600850928/ref=sr_1_1?ie=UTF8&qid=1378127713&sr=8-1&keywords=spray+finishing+made+simple

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.