Recommended Posts

Posted

Realized yesterday that I have lots of credit card reward points mostly built up from work travel. I exchanged enough of them for amazon.com gift cards to get the Festool OF1400 I had been planning as my next tool purchase. I am so excited!

I will have enough to get the router, one section of guide rail(track saw in the future) guide stop for track, and an edge guide.

It will sure beat my old craftsman with no dust collection. That thing makes an absolute mess everytime I use it. Still can't figure out how chips go so far! I will be using it with my shop vac with a 2 1/2" hose. What will I need to make the hookup work to the router?

Is there anything else I should know before making this purchase?

  • Like 1
Posted

You'll like that router.  Normally the "holey" rail costs $1 more than the un-holey rail. The holey rail can be used for all the same things as the un-holey, but can also be used with a guide plate that is part of the LR-32 system.  Basically you can index the router by 32mm steps.  Wish I knew of the price difference when I bought some of my rails; I knew when I got the 3000, but rightfully that one doesn't come in a holey option :)  Get the holey rail; you can easily make your own jigs to take advantage of the holes (at least I would!)

 

You'll need an adapter for your shopvac hose to the 25mm OD dust port.  Fein has a lot of adapters that would work and I found them at Woodcraft; take the hose with you to try before you buy or you'll be makin' trips...

Posted

You'll like that router.  Normally the "holey" rail costs $1 more than the un-holey rail. The holey rail can be used for all the same things as the un-holey, but can also be used with a guide plate that is part of the LR-32 system.  Basically you can index the router by 32mm steps.  Wish I knew of the price difference when I bought some of my rails; I knew when I got the 3000, but rightfully that one doesn't come in a holey option :)  Get the holey rail; you can easily make your own jigs to take advantage of the holes (at least I would!)

 

You'll need an adapter for your shopvac hose to the 25mm OD dust port.  Fein has a lot of adapters that would work and I found them at Woodcraft; take the hose with you to try before you buy or you'll be makin' trips...

I think that is good advice Paul! I have a 1080 "holey rail" and have been really thinking about what jigs I can make with it. I should get a 20mm router bit and make some holes in my outfeed table for MFT accessories.

 

Congrats on the purchase, the OF1400 is a nice router. One thing I learned recently is that when the port for the dust extractor is connected, the little green clip that locks the port in place makes it difficult to use stops when routing in between two points. 

 

Enjoy the router!

Posted

Ok ok.....The only green things I own are a Grizzly table saw and my Kermit the Frog underwear.  Before I would jump on the Festool I'm going to have to determine if this fast moving, big green, high ticket trolley car is a popularity thing or is it really that much better?

The litmus test question is....Is this Festool OF1400 really better than 5 Porter Cable routers??? 

2 Makita COMPLETE kits???

  • Like 1
Posted

I have a few routers and at the end of the day, they all do the same thing.  However, none of them do "dust collection" as well as my OF1400.  I love the fact that I can use my tracks with it and the built in stops.  It's nice to be able to repeat a process with minimal adjustments for each step.

 

It's a lot of money to put out for the OF1400 but, I have never regretted the purchase.

Posted

Ok ok.....The only green things I own are a Grizzly table saw and my Kermit the Frog underwear.  Before I would jump on the Festool I'm going to have to determine if this fast moving, big green, high ticket trolley car is a popularity thing or is it really that much better?

The litmus test question is....Is this Festool OF1400 really better than 5 Porter Cable routers??? 

2 Makita COMPLETE kits???

I am not sure.  I currently don't own anything Festool.  I have two reasons for making the choice, dust collection and being able to use the tracks with built in stops as TIODS said.  

 

I looked long and hard at other routers, but none of them seem to integrate as well with other useful and necessary components.  I could definitely still be convinced otherwise but those features are important to me.  

 

Josh

Posted

Ok ok.....The only green things I own are a Grizzly table saw and my Kermit the Frog underwear.  Before I would jump on the Festool I'm going to have to determine if this fast moving, big green, high ticket trolley car is a popularity thing or is it really that much better?

The litmus test question is....Is this Festool OF1400 really better than 5 Porter Cable routers??? 

2 Makita COMPLETE kits???

I own a few Festools and there are features that separate them from the pack, if you are willing to pay. At the end of the day a PC router and the OF1400 will both...well route! I will say that working in a garage shop where I share space with other "stuff" the dust collection alone is worth the premium. I also like being able to put the router on a guide rail, makes cutting dados easier. I don't own everything Festool makes, far from it but the Festools' I do have working very nicely in my shop and work flow and would not have it any other way. 

Posted

One thing about that Makita router - it doesn't accept 1/2" bits. When I was doing my PC vs Bosch comparison in the other thread, I had original looked at the Makita kit as well (since it's about the same as the Bosch kit) - but that killed it for me.

Posted

One thing about that Makita router - it doesn't accept 1/2" bits. When I was doing my PC vs Bosch comparison in the other thread, I had original looked at the Makita kit as well (since it's about the same as the Bosch kit) - but that killed it for me.

Yeah.....I just grabbed a 'kit' for a point.  I own a Makita 1101 and it takes 1/2 bits but I'm just making a comparison - 2 for 1

Posted

My OF 1400 showed up today. What an upgrade from my old hand me down Craftsman. I am not even sure what decade that thing was built. Have not had a chance to use it yet but hopefully in the next day or two I can make some sawdust with it.

I am waiting for the dust deputy that I ordered for my shop vac. I have to get some better dust control. Some sort of DC system is next on my list for my bigger tools. At this point I think I am going to with the Harbor Freight 2hp with a Super dust deputy attached. Haven't decided if I will vent outside or get a Wynn filter. My big tools are clustered well enough at this point I really shouldn't need to move it around in either circumstance.

Josh.

Posted

I got my dust deputy setup tonight so I gave the new router a try. What an amazing tool. Where has this router has been all my life? Very smooth and very little dust escaped.

Very happy with my purchase. I have a bunch of 1/4" roundovers to do soon, can't wait to get started.

I really can see how people get sucked into Festool tools. Everything is just so well done from the systainer to the thought put into the tools.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 56 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined