Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Dewaxed Shellac Question

Featured Replies

I am finishing a pretty large project.  Spent the better part of the afternoon appling a 1lb cut of Dewaxed Shellac(SealCoat).

 

I am planning to use a wiping poly next.  Just curious if there is any advantage in doing multiple coats of dewaxed shellac?  

I am just curious more than anything.  

 

Josh

A couple coats of shellac will fill the wood grain faster than trying to build up a wipe on finish to do the same thing.

I like to rub in multiple coats of very thin shellac. This seems to work the shellac deep into the surface, giving a smooth, well-sealed surface, but without much buildup. One or two coats of wipe-on poly after that leaves an awsome finish, without the appearance of a plastic coating.

  • Author

A couple coats of shellac will fill the wood grain faster than trying to build up a wipe on finish to do the same thing.

 

 

 

I like to rub in multiple coats of very thin shellac. This seems to work the shellac deep into the surface, giving a smooth, well-sealed surface, but without much buildup. One or two coats of wipe-on poly after that leaves an awsome finish, without the appearance of a plastic coating.

 

So do you guys sand between coats?  The shellac is much easier to apply than poly, so maybe I will do another coat. 

I don't sand, because the mixture I use is thinner than a 1-lb cut, and I just rub it in with a rolled-up rag. Each coat dissolves a bit of the coat beneath, merging them together and helping to smooth everything. The trickiest part is keeping the edge wet, because the denatured alcohol evaporates so quickly.

 

I am planning to experiment with a little BLO added to this mix, and see if that helps lubricate the edge and slow the drying time a little.

I don't sand, because the mixture I use is thinner than a 1-lb cut, and I just rub it in with a rolled-up rag. Each coat dissolves a bit of the coat beneath, merging them together and helping to smooth everything. The trickiest part is keeping the edge wet, because the denatured alcohol evaporates so quickly.

 

I am planning to experiment with a little BLO added to this mix, and see if that helps lubricate the edge and slow the drying time a little.

 

I have done a similar technique quite a few times.  I only sand when I run into problems, like dried lap marks.  I sand those very lightly with 300 grit paper (or whatever high grit I have) until smooth to the touch.  I don't worry about what it looks like because the next coat of shellac will dissolve the foginess and make the lap mark invisible.  I do lightly sand before my final coat, just to make sure everything is nice and smooth. 

The thing to remember about using multiple coats of shellac is that the coats blend - that is to say the second coat will soften and blend with the first coat.  Any sanding done between coats will therefore be undone and proven unnecessary.

You need something to sand...  A single application of #1ct really doesn't apply enough solids...  I'd apply another #1ct, the lightly scuff with something like a #320 Rino sanding pad.  Really, two coats of #1ct lightly sanded doesn't leave that much behind...  It depends on where you want to go from there -- you could go directly to poly or apply a #1.5ct, scuff then poly...  Your choice...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.