Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Blending walnut

Featured Replies

I usually cut and glue up walnut with a "show side" and hidden side mind set if trying to minimize the sapwood appearance. But if you have already built the piece try whatever walnut stains you have available . Mask off the areas around the sap wood on some scraps and see how close the color is . Once you have picked a stain and stained the masked sapwood areas you can make a wash by thinning the stain and use that to blend around the stained areas. It takes practice to make this look good, do not practice on your project!

Dyes may give you good results. Start out with weaker concentrations and sneak up on the darkness needed.

I have seen professional finishers seal the wood then use an air brush to tone the sap wood. I often spray my stain and then wipe back the excess. Areas that turn out too light get a lite misting coat that gets carefully wiped to blend it in. Thin cardboard can be cut and used as a spray shield to prevent overspray on surrounding heartwood.

I would explain to the client that staining the sapwood is going to be an extra expense. If it was specified up front then you will have to fix it at no charge. Think of it as a learning experience, one you will never forget.

Always explain that woods like cherry and walnut have a certain percentage of sapwood and there is a 35% up charge to cut out all the sapwood from the face surfaces. 50% up charge to have no sapwood visible at all due to the time and expense of so much extra wood..

==> blending walnut sapwood to look more like the heartwood?

 

A good technique is to get an airbrush and 'spot' dye the sapwood with an alcohol-based dye...  Investing in an airbrush is really not that big a deal -- like $39.95 (as long as you've got a compressor and regulator)...

 

Now here's the rub, walnut lightens over time (as do most woods ending in 'nut'), so you've got the leave the sap a bit lighter and let the rest of the stock catch-up... 

 

As a side note: airbrushes are the 'secret weapon' for many pro finish shops... it's amazing what trouble they can get you out of...

  • Author

...

I would explain to the client that staining the sapwood is going to be an extra expense. If it was specified up front then you will have to fix it at no charge. Think of it as a learning experience, one you will never forget.

...

 

 

Wdwerker - that might work if I wasn't married to her!  :)

 

 

...

As a side note: airbrushes are the 'secret weapon' for many pro finish shops... it's amazing what trouble they can get you out of...

 

 

HHH - Thanks for the idea, I do have an airbrush on hand, but it was purchased for my son's art projects. I don't usually do sprayed finishes, and never though about using it.

Toneing with a spray gun is a lot easier than toneing by hand. It useful for cherry too.

They also sell steamed cherry and walnut that evens out the heartwood color throughout the board. You can check those out next time. I don't know much about them, except that the option exists.

Air dried walnut and cherry has a much better range of color. When they steam it it muddies the colors and dulls the heartwood to make some improvement to the appearance of the sapwood. I really prefer the look of air dried walnut there is a range of colors and intensity in a single board. Curly grain is particularly varied in rich tones but it falls flat when steamed.

Either educate yourself to her preferences in advance or start practicing with the air brush.......

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.