Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Cherry - use a conditioner or not

Featured Replies

I was told to use a conditioner on new cherry if you are staining it to avoid blotching.  Does anyone have experience with these?  

Cherry is quite blotch prone...  there are entire websites dedicated to successfully coloring cherry...  I listed a bunch of them on another "coloring cherry" thread...

 

In fact, if you don't have access to decent spray gear, I'm not sure you can successfully color cherry at all...

 

But the first question is the most important, should you be coloring cherry at all?

 

I can understand if you want to blend sapwood... there are specific techniques for that...

 

I can also understand if you want to equalize a panel glue-up... there are "equalizer" schedules as well...

 

But beyond those two specific cases, I can't see much merit to coloring cherry... It simply ages so well, that coloring cherry (beyond placing the piece in direct sun for an afternoon) doesn't really improve the character of the wood...

But beyond those two specific cases, I can't see much merit to coloring cherry... It simply ages so well, that coloring cherry (beyond placing the piece in direct sun for an afternoon) doesn't really improve the character of the wood...

Agree with this. Unless you're dealing with a customer or someone who simply doesn't understand this or understands it but doesn't want to wait, I think you're much better off leaving the piece outside for a couple afternoons and then using a clear topcoat.

Obviously taste is subjective though.

If you are hand appplying, skip the wood conditioner and try a gel stain.  I can't speak specifically for cherry, but I have used General Finishes Water Base Wood Stain (not the dye, but the thick creamy stuff) on Birch (also very block prone) and it worked great with no conditioner.   Same goes with Old Masters Gel Stain, it works well on blotchy woods.   You will have better luck with pigment stains that stay on the surface than with dye stains that penetrate.  My first attempt on the birch with a dye stain was pretty ugly.    I think the wood conditioners work under the same principal, they keep the stain from penetrating into the wood and highlighting the blotch.  So might as well skip a step and use a stain designed to sit on the surface, if you must stain.  

==> try a gel stain

 

Gel stains are great products -- and well suited to several situations.... I use them myself... 

 

BUT, the part that mfg's don't mention, is that they muddy the surface grain badly...

 

So please, not on Cherry...

==> try a gel stain

 

Gel stains are great products -- and well suited to several situations.... I use them myself... 

 

BUT, the part that mfg's don't mention, is that they muddy the surface grain badly...

 

So please, not on Cherry...

 

Yeah, totally agree.  I think it was well-established that we were all against staining cherry.  This was a "if you must" suggestion.  Thanks for "clarifying" my "muddy" suggestion. 

I was told to use a conditioner on new cherry if you are staining it to avoid blotching.  Does anyone have experience with these?

Its your wood I dont care if you want to make it barney purple. Would be helpful to know if your hand applying or spraying. If your spraying its very easy to prevent blotching. Hand applied its also doable but different so knowing application method is a must to give you a direction to go.

  • Author

Thanks to everyone for their comments.  The person receiving this wants it colored otherwise I would not do it.  The Rockler store recommended General Finishes Gel Stain and to use the conditioner first.  Perhaps I should present my client some examples and see if they are satisfied.  You all have me sufficiently worried now but I was the one who asked for help.

Thanks to everyone for their comments.  The person receiving this wants it colored otherwise I would not do it.  The Rockler store recommended General Finishes Gel Stain and to use the conditioner first.  Perhaps I should present my client some examples and see if they are satisfied.  You all have me sufficiently worried now but I was the one who asked for help.

You don't need to condition for gel stains.

And you can try sealing the wood with shellac and then going over with your stain followed by your clear.

You probably already know this Pete, but I will mention it: Use large enough scraps for your sample boards..... DAMHIKT!

  • 4 weeks later...
  • Author

REPORT: I stained the cherry with GF Gel stain and I can report that you are all correct about the blotch.  Some sections look stunning and others look like it was dragged through the mud.  I'm not giving up on cherry however it may be the last cherry piece I will ever stain.

Another option is to use a "spit coat" of shellac (2 parts unwaxed shellac (Zinsser's Bullseye Sealcoat) to 3 parts denatured alcohol (Behlen Behkol)) to prevent Cherry blotching. An unwaxed shellac allows other varnishes to be used, if needed. I don't stain Cherry, but Zinsser's literature says you can put stain over the spit coat if needed.

It's always a great idea to try whatever on scrap pieces of the project's wood to test finish, color, etc. before you do anything to the finished piece.

Pete, if its that bad, you may want to change techniques on this....

 

Try a factory finish:

 

First put down a spit coat of shellac - spray if you can. Let it set up for a good 1/2-1 hour so that all the alcohol is evaporated. Next, spray on a mixture of transtint in denatured alcohol. The alcohol will "burn" the color into the shellac evenly if sprayed. Let this set up. Top coat with a layer of shellac, continue to build up coats with shellac or waterborne poly.

 

I have use this method on pine and it works fine.

 

IMG_20120919_135933_zps4ae3422c.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.