Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Is it Possible to Even Out an Aged Pine Patina?

Featured Replies

Hello. I know very little about wood finishes, and would be very thankful for some advice. I recently acquired a vintage drafting table. It was made by the Mayline Company in Mighigan in the 1950s. The top is planks of solid pine, and the base and legs are solid oak. It's a very solid and chunky table, and the wood is stunningly beautiful. I want to maintain the table top's original finish, even though it has darkened in an orange-ish hue. (I actually like it that way.) I believe that it has some type of hard finish, because I can see a dull light reflection off of it. However, the finish is clearly old to the point that the piece was able to absorb some mineral oil.

 

Here's an issue I do have with it, and wondered if there were a cure without ruining the original patina. Being a drafting table, it apparently had a very large piece of paper or other covering over two-thirds of its surface--likely for decades. This resulted in the wood underneath the covering being protected. As a consequence, the third of the table top that was always uncovered has a darker patina, and there is a clear dividing line between these two colors that runs the entire width of the table where the edge of the paper was. Does that make sense? I was just wondering if the exposed area is darker because of dirt or oil? (Washing the piece did not help.) Or does exposed wood just darken more over time, and that's just the way it's going to be? Any advice on evening out the color would be very much appreciated!!  

My only thought would be to put paper over the darker third.  A few decades down the road & you should be all set.

 

Sorry, I can't think of anything more realistic, other than removing the patina & using steel/tea/vinegar to quick age it.

Reproducing "age" is one of the hardest things to do in finishing. It is often easier to just sand it all down and start over. You'll lose the patina for a short time, but eventually it will return. You might try a few short-cuts, like Oz suggested, or use a shellac finish with an orange tint.

i would just leave that darker third part... it probably looks cooler that way IMO. if you want to even out the wear, sand the whole thing down and do a colored briwax coating. that will give you a pretty even aged look. other options include blow torching, steel wool, vinegar etc. basically, that finish on the darker part is gone and you need to break down the existing finish before you start adding color for a true match. 

 

pics would help! can you post some pics?

If you're going to be using it as a drafting table, putting a proper cover on it is well worth it anyway.  That's probably what was on it to start with.  Only use double stick tape at the top and let it hang.  It'll buckle if you use tape in other places under it.

 

http://www.ebay.com/itm/Drafting-Table-Cover-VYCO-Green-Cream-36x48-/390225961150?pt=LH_DefaultDomain_0&hash=item5adb47a0be

  • Author

Thanks very much for your replies. Given your feedback, I think I'd like to leave its appearance as it is. In that case, how best to protect its very old original finish? It has a very worn-out laquer or some such finish on it, and the wood scratches very easily. I can oil these out, but they kind of return when the oil soaks in. Will the scratches come back after a while, even after I put a protective coating on it? And for a protective coating, if I only use paste wax, that might not protect it much, and then I can't ever put a harder finish on it without stripping it, right? What kind of truly protective coating can I put on it that will not show, or change the feel, or look of it? I don't want it to look all shiny and new, or fake, as that will not match the vintage looking table legs, etc.... I'm attaching a couple of pics here, thanks!!! 

post-14601-0-04169900-1381773042_thumb.j

post-14601-0-52249800-1381773054_thumb.j

Thanks very much for your replies. Given your feedback, I think I'd like to leave its appearance as it is. In that case, how best to protect its very old original finish? It has a very worn-out laquer or some such finish on it, and the wood scratches very easily. I can oil these out, but they kind of return when the oil soaks in. Will the scratches come back after a while, even after I put a protective coating on it? And for a protective coating, if I only use paste wax, that might not protect it much, and then I can't ever put a harder finish on it without stripping it, right? What kind of truly protective coating can I put on it that will not show, or change the feel, or look of it? I don't want it to look all shiny and new, or fake, as that will not match the vintage looking table legs, etc.... I'm attaching a couple of pics here, thanks!!! 

You can't alter the characteristics of pine or any softwood with a finish. Let alone wood. Its going to dent and we'll just have to live with it.  

That thing looks great! I can barelly notice the warn section. Just leave it be. If you want to seal everything in just do a waterbased poly over the top. Satin will not give much sheen to it or you could use the matte poly from rustoleum. Dont over think it here... If that desk has lasted this long it will keep on going

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.