Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Too cold to spray?

Featured Replies

I was half-way though finishing my WW guild blanket-chest when the Texas weather decided to go against me and drop nearly 40F overnight. It's now about 38F and I'm wondering if it's not too cold for outdoor spraying?  I'm spraying General Finishes Enduro-Var via HVLP. I know colder weather extends dry/cure time, but will it have another side-effects? Or should I just wait for it to warm up a bit?

 

Thanks

I recently did some finishing with HVLP and it's been very cold here.  I sprayed outside and then moved the piece indoors to cure.  Not very convenient but, it did work just fine. 

 

I was using water based stuff so there really wasn't any fumes to deal with.

Too cold....call it a day, surrender and all the stuff. I know its hard to do when your pushing to get it done. Wait out the cold. The finish wont flow and level out right. Plus, your finish will stay wet longer allowing dust or other crap to contaminate your surface.

 

-Ace-

==>   I'm spraying General Finishes Enduro-Var via HVLP.

 

I looked over the data sheet...  Funny, it doesn't give temp ranges.  With no other info to go on, my gut feeling is that you should wait until it's warmer.  Id give the GF tech line a call and ask for their tech specs and temp ranges...  Bet they can help...

If you use Facebook General Finishes are on there and you can ask questions direct. They normally answer queries pretty quickly using that route.

I use EnduroVar thru HVLP and in general spray at 60 or above indoors. Personally I think 38 is too low to be spraying this but GF will be able to confirm.

At the last resort you can heat up the gun at the sink with warm water and putting the can of finish (closed) in a pot filled with water. This will allow the finish to flow better, mind you the finish will reduce viscosity. So if you're spraying vertical surfaces watch out.

After spraying bring it in the garage if you can. Don't let it sit in the snow. :P Do a test first though.

I guess I should have noted that when I sprayed outdoors in the cold, everything was moved out for the spray (about 10 minutes) and then moved right back in. 

 

I was using GF and had no issues.

I really would not recommend it.   Most curing finishes, regardless of the solution base, stop curing properly somewhere around 4-6 deg C (39F-42F).  Just above that range, they will cure slowly, but should be fine.    The key part is not the actual spraying, but the curing.   You may see layers form, cracks, seams, etc.

 

I speak with some experience...right now it is 19F outside, my garage finishing area may not be back above 35F until April.   I normally try to confine my winter finishing projects to shellac and similar benign finishes, but I have made a bit of a mess of that this year with 3 projects that I did not quite get done.

 

At least down in Texas you can wait a week or so and be back in business.

  • Author

Thanks everyone for the advice! My gut told me that it was too cold but I wanted to confirm anyway. As Arminius said, I'll probably have to wait a week max for the temp to go up :). 

hey guys newbie here on the forum thing cool way to get some great insight from all you guys as far the cold spraying Ive done it when its pretty chilly out never had any bad effects but as the other poster said the dry time is way longer allowing for crap to get on your pretty newly sprayed whatever the only reason I did it was I build cabinets for a living and my last shop was full of dust and ongoing cabinet building so I had to finish a few jobs out in the enclosed but open ended carport type of structure sometimes the show must go on lol  I was using a hvlp cup gun at the time spraying cambells white laquer thanks for letting me hang around

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.