Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

My resaw sucks! Need diagnosis

Featured Replies

I have a Ridgid 14" 3/4 Hp bandsaw. I know it's not a resaw machine. I use it mostly for cutting curves. Anyways, I had a 4/4 5" tall aromatic cedar board that I wanted to resaw into 2 equal pieces. Cedar is soft. A hard sneeze will cause some tearout. I didn't think this was too tall of an order, even for my little underpowered Ridgid. I have a bosch 1/2" blade (that is starting to dull if I'm being honest). It's perfectly square to my table and had plenty of tension. I took my time with a slow feed rate and split the center line perfectly......on the top edge of the board. On the bottom, it was so far off center I had to toss to the burn pile. What's my problem here? Besides not having a powermatic 1800.

 ...blade (that is starting to dull if I'm being honest).

 

You answered your own question.  Grab a new 3TPI and I bet you find you're back in business.

  • Author

You answered your own question.  Grab a new 3TPI and I bet you find you're back in business.

 

this is what i suspected.  thanks for the feedback

For resawing, blades have to be perfectly sharp. They may cut fine for other cuts but won't resaw at all. This is especially true with lower tension and low hp.

Steve

For less than sharp blades when resawing especially in very hard woods I will use a thin kerf blade in the tablesaw and rip both sides of the board, then finish the cut on the bandsaw. Yes it does start out with a wider kerf loss, but by the time you flatten the board I find it's about the same.

With a new sharp resaw blade and careful set up I just go straight to the bandsaw. If I am cutting multiple slices off the same blank I flatten the face of the blank between slices.

Let's not overlook the simpler explanation, was the board flat to begin with?  Putting a cupped board against the fence would get you what you describe.  With a dull blade I may have problems with drift but it's not going to cause the cut to be at an angle.  But I think my Delta has the lower guides closer to the underside of the table than your Ridgid so I guess if the blade bowed in the cut it could do that.  But I resaw a lot of cedar and the blade needs to be more than a little dull to even notice it's cutting it.  Since putting on carter guides I go a lot further resawing on a dull blade.  I figure they are going to pay for themselves eventually.

  • Author

Let's not overlook the simpler explanation, was the board flat to begin with?  Putting a cupped board against the fence would get you what you describe.  With a dull blade I may have problems with drift but it's not going to cause the cut to be at an angle.  But I think my Delta has the lower guides closer to the underside of the table than your Ridgid so I guess if the blade bowed in the cut it could do that.  But I resaw a lot of cedar and the blade needs to be more than a little dull to even notice it's cutting it.  Since putting on carter guides I go a lot further resawing on a dull blade.  I figure they are going to pay for themselves eventually.

 

yeah, the board was jointed and planed.  no fence…..i freehanded the cut on a scribed center line that was half the thickness of the board. 

yeah, the board was jointed and planed.  no fence…..i freehanded the cut on a scribed center line that was half the thickness of the board. 

 

If it was the blade being dull I would expect that the cut would have started out even on both sides and then got progressively worse.  I wouldn't really recommend trying to resaw something as thin as 4/4 without a fence.  It really doesn't take much of an angle to screw you up.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.