..Kev Posted December 22, 2013 Report Posted December 22, 2013 Even though this is the journal section, I'll start out by apologizing for a long post. Also, there is an injury picture in this one so, if that bothers you, please ignore the rest of this post. Background - My original out feed table was a very crudely built piece for my shop. It was dead flat and did its job. However, as projects rolled through my shop, I found myself doing more and more work on my out feed table instead of moving the work to my bench. Although I tried to break this habit, I failed. So, rather than feeling guilty for doing the work on the out feed table, I decided to upgrade the table to increase efficiency and work flow. Here's the original out feed table: The T track in the top was added later to help with clamping as I found myself working more and more at this table. The drawers were added later as well as I got tired of walking across the shop for items from my bench. Likes and dislikes - There was a lot of things about the old table that I liked. It had a super stable base and was dead flat. The added drawers and the T-Track was a huge help as well. What I didn't like was that it had no vise or means for working long boards vertically. I also didn't like the fact that my CT didn't fit underneath it so I was constantly moving it to use my router table. I also wanted more ability on the surface to clamp things down like you get with the Roubo. Now before the haters get going, I know this is not a Roubo by any means. The build - Since I liked the original stable base, I went with similar construction with some improvements. All the joints are mortise and tenon with draw board dowels. 4x4s for legs I also added two 2x12s on the end to create a hold fast system on that end. I left room on either end to account for a vise on one side and the hold fasts on the other. The left over space in the middle was used for drawer space. All of the structure was jointed flat. As there was about 24 hours between milling and assembly, I noticed a couple high spots in the lumber so, they were milled with a hand plane until everything was dead on. The drawers were all done in 3/4 Hemlock, 1/2 blind dovetails, and full extension glides. The top is Birch. My original plan was just to use MDO but, when I got to my lumber dealer, the birch was about 5 bucks a sheet cheaper so, what the heck, it looks better with a finish anyway! Rather than one T-track, I decided to add one near the front as well as one near the back. I also left room on either side to fit parallel clamps under it for additional clamping ability. I trimmed it out with Maple and tossed in a few walnut plugs to hide the screws. The drawer fronts were also done in maple. This was all finished with Arm-R-Seal to help with the abuse this table will see. My small Lee Valley vise on the other end was back ordered so will be installed when it arrives. I have some other projects that need doing so, will get back to that soon! The Injury - The very first 4x4 that I hauled into the shop is where the injury happened. When you drop something, it's a natural reaction to try to catch it. Well, that's what I did. Even though I had gloves on, I smashed my middle finger between that 4x4 and my bench. Yep, that's right, the bench that I don't use as I should. Long story short, it's broke and should have gotten a few stitches. I've been and EMT/Firefighter for many years so, just doctored myself up and got back to work. Still got some healing to do but, it's coming along nicely! Closing - Still some details to finish up. I'll try to snap some pics and update the details as I get them finished up. Again, sorry for the long post and "thanks" if you got this far! Quote
..Kev Posted December 22, 2013 Author Report Posted December 22, 2013 Figures, posted this in the wrong section... Meant to post in journal section, sorry! Thanks for the move Beechwood! Quote
Llama Posted December 22, 2013 Report Posted December 22, 2013 Great work! As for the finger, ouch! Quote
..Kev Posted December 22, 2013 Author Report Posted December 22, 2013 Thanks Mel! Finger is healing nicely. Quote
G S Haydon Posted December 22, 2013 Report Posted December 22, 2013 Bad ass TIODS, slap some aprons on that any you got yourself a Nicholson :-). And that finger, I can feel that pain! Love the diy med. Quote
..Kev Posted December 22, 2013 Author Report Posted December 22, 2013 Thanks Haydon! Still kicking around some ideas.. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.