dwacker Posted December 31, 2013 Report Posted December 31, 2013 Im going to order a couple dedicated saws and the 1023rlx seem to look like they would fit the bill. One will be stripped for dado only and the other will be stripped for a rip only. For those that have this saw how would you rate the dust collection? Is there backlash in the elevator? If so could you tell me how much. Thank you Quote
Dan S Posted January 1, 2014 Report Posted January 1, 2014 I don't own a 1023, but everything I have read by people who do said it's not that great, hence the reason i got a G0690. It's supposed to be poor because the shroud hose is only 2-1/2" and that feeds into the 4" dust port. Quote
Freddie Posted January 1, 2014 Report Posted January 1, 2014 Dust collection in our tools seems to be a crap shoot. Also seems that a lot of people on this forum with a little engineering tweaked their setups to work for them. I wish the companies would take care of this before hand. 1 Quote
tim0625 Posted January 1, 2014 Report Posted January 1, 2014 I have a 1023 and the dust collection isn't good. It often collects in the corners so eventually, the collection of dust and chips makes the bottom of the saw look like a bowl. I occasionally remove the throat plate, turn on the dust collection and spray air from the top to stir things around until it's clean. There was a thread on here a couple years ago where someone modified their 1023 DC just a little and it made a big difference. If I were buying it again, the DC isn't a deal breaker but it needs to be better. As far as the elevator, I haven't had issues there - it's really tight with no backlash. I've been really satisfied with the saw. Quote
knotscott Posted January 1, 2014 Report Posted January 1, 2014 There are so many variables involved...it's hard to know how much pertains to the saw vs the DC system and setup. Quote
wooddok Posted January 7, 2014 Report Posted January 7, 2014 Can`t wait to hear your impressions of these saws! I would really like some Very good close up shots of the trunnion and the table top as well if that's possible after you receive them. I understand from talking to Grizzly that these ride on mitre slots and are the workhorse saws. Quote
dwacker Posted January 7, 2014 Author Report Posted January 7, 2014 Can`t wait to hear your impressions of these saws! I would really like some Very good close up shots of the trunnion and the table top as well if that's possible after you receive them. I understand from talking to Grizzly that these ride on mitre slots and are the workhorse saws. We will see I ordered the W version. My guys have a $25 bet going as to wether or not it will make it off the pallet. Both of them have experience with Grizzly saws so Im a little concerned. Quote
Dan S Posted January 8, 2014 Report Posted January 8, 2014 We will see I ordered the W version. My guys have a $25 bet going as to wether or not it will make it off the pallet. Both of them have experience with Grizzly saws so Im a little concerned.I think you will be fine. Usually the people that complain about Grizzly are people who thought they would get a $2500 machine for $1200. 1 Quote
sunadmin Posted January 8, 2014 Report Posted January 8, 2014 I agree with Dan S. I own several pieces of Grizzly stuff and I love every piece, they are all high quality customer service is great price is right. Yes they are import but so is everyone else except I think Powermatic.. those guys charge 9000 for a 1200 table saw though. Quote
dwacker Posted January 8, 2014 Author Report Posted January 8, 2014 I agree with Dan S. I own several pieces of Grizzly stuff and I love every piece, they are all high quality customer service is great price is right. Yes they are import but so is everyone else except I think Powermatic.. those guys charge 9000 for a 1200 table saw though. Well I dont think PM charges $9000 for a $1200 table saw. I dont have a lot of experience with Grizzly and took a leap of faith with this saw. That being said I do have quit a bit of experience with their shapers and large bandsaws the quality level is not even close to that of Powermatic but either is the price so I guess you do get what you pay for to some degree. There does come a point where there is a line between acceptable lesser quality and not. I think that line moves with the different buyers. For example: You one one hand may think dealing with the garbage fence on a Grizzly shaper or the backlash in elevator not a big deal, but you only use it a few time a year. I on the other hand use mine everyday and need to expect that its elevator is accurate and its fence is repeatable day in and day out. I also need to consider the dust collection, safety features, motor adjustment and spindles. You really have none of those concerns you will probably never wear out a belt let alone a spindle. Its all relative. When we talk about saws and things of that nature and you do some reading on the forum. Pay attention comments like how often folks are having their saw blades sharpened. Some are once a year or every few years some like me get a week or two at very best out of a blade before its ready to go out. Now call Grizzly and ask them for a set of arbor bearings or a motor starter before making the purchase 9 times out of 10 they can't supply you with the replacement parts because they dont know what parts they put in the saw or they have to come from the factory months away with powermatic that doesn't happen. The reality is for most, their tools are garage queens and spend most of their time left in complete silence. For some of us we turn our saw, shaper, dust collector......... on in the morning and dont shut them down until the end of a work day. Quote
Dan S Posted January 8, 2014 Report Posted January 8, 2014 Well I dont think PM charges $9000 for a $1200 table saw. I dont have a lot of experience with Grizzly and took a leap of faith with this saw. That being said I do have quit a bit of experience with their shapers and large bandsaws the quality level is not even close to that of Powermatic but either is the price so I guess you do get what you pay for to some degree. There does come a point where there is a line between acceptable lesser quality and not. I think that line moves with the different buyers.That's kind of my point though, most of the people I hear complaining on the internet want top end model features/finish at economy pricing. Like the one guy I know who purchased a Harbor freight angle grinder to replace an old industrial grade Milwaukee. I lit his ears on fire when he started ranting to me about it. Honestly a $20 tool Is never going to be as good as one that cost almost 10 times as much. Quote
wooddok Posted January 18, 2014 Report Posted January 18, 2014 PB did you ever get your 1023`s? Being in Tacoma I would think they were easy and quick if they were in stock. Quote
dwacker Posted January 18, 2014 Author Report Posted January 18, 2014 PB did you ever get your 1023`s? Being in Tacoma I would think they were easy and quick if they were in stock. We got one but haven't touched it yet. I'm buying a new building and it will go in there after we close. For now it will sit in the storage unit for a few weeks. Quote
Freddie Posted January 18, 2014 Report Posted January 18, 2014 Did you at least inspect it before the freight truck left? How was everything along those lines? My jointer had damage due to improper crating, but it was nothing operational, merely cosmetic. Quote
dwacker Posted January 19, 2014 Author Report Posted January 19, 2014 Did you at least inspect it before the freight truck left? How was everything along those lines? My jointer had damage due to improper crating, but it was nothing operational, merely cosmetic. It looks fine. This one is not getting the table wings so I don't care if they are flat or not, going to be scrap metal anyways. The base is cheap for lack of better words and the casting in general are ugly but I don't care. I wouldn't buy one for anything more than what we are using this saw for which is a narrow rip saw. The reviews about quality are defiantly overstated but like I said for this it won't matter much. Quote
Spencer_J Posted January 19, 2014 Report Posted January 19, 2014 Congrats on the new building!! Did you end up taking on that job for all of those kitchen cabinets? Sent from my thumbs Quote
dwacker Posted January 20, 2014 Author Report Posted January 20, 2014 Congrats on the new building!! Did you end up taking on that job for all of those kitchen cabinets? Sent from my thumbs Yes been working on them for months. Also took on more and am turning it all over to the kids. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.