Godet Posted October 10, 2010 Report Posted October 10, 2010 I just set up my JET 10" Jointer/Planer. I've got the blades set to the right depth across all 10"....however, when I run boards through, they are essentially "spring jointed" with a slight concave shape. Two boards edged by the jointer will fit properly together at the ends (about the first inch to 2 inches on each end) however, I can see through about 1/32-1/64 at the center. Seems like I might be doing something wrong in my technique--any ideas? Quote
Dan S Posted October 11, 2010 Report Posted October 11, 2010 I just set up my JET 10" Jointer/Planer. I've got the blades set to the right depth across all 10"....however, when I run boards through, they are essentially "spring jointed" with a slight concave shape. Two boards edged by the jointer will fit properly together at the ends (about the first inch to 2 inches on each end) however, I can see through about 1/32-1/64 at the center. Seems like I might be doing something wrong in my technique--any ideas? Sounds like your out feed table needs alignment. check out these links, they should help. http://home.usmo.com...ng/jointer.html http://thewoodwhispe.../jointer-setup/ When I tune my jointer, I use a test bar like described in this article. http://www.finewoodw...DF.aspx?id=2643 Quote
woodwhisperer Posted October 11, 2010 Report Posted October 11, 2010 If you can get that tool set up properly, you're a better man than I am! I tested one of those out and for the life of me I couldn't get a proper jointed board off it. I normally love Jet products but that's one that I had some serious issues with. Quote
Godet Posted October 11, 2010 Author Report Posted October 11, 2010 If you can get that tool set up properly, you're a better man than I am! I tested one of those out and for the life of me I couldn't get a proper jointed board off it. I normally love Jet products but that's one that I had some serious issues with. Thanks guys. Marc, I just watched you're instructional video on setting up the jointer--which greatly raised my spirits...this response, however, has demoralized me. Oh well...I'll give it a try tomorrow...I had read good reviews elsewhere on this model and the guys I trust at Woodcraft thought it was OK. I'll post my results here.... Quote
PurpLev Posted October 11, 2010 Report Posted October 11, 2010 sounds like your outfeed table is lower than the cutterhead/blades. Quote
Juicegoose Posted October 11, 2010 Report Posted October 11, 2010 I wouldn't go as far as to say your outfeed table is lower. It might be the table is sagging though. You wouldn't think it's possible in anything but wet particle board and older women but it happens. Like Marc recommends in his video pick yourself up the lee valley aluminum straight edge(longer the better) and get out your feeler gauges. clamp that straight edge to the outfeed table and measure the fore and aft section on the infeed table. I had similar problems and ended up shimming the outfeed table to be coplaner. I'm using an older Ridgid jointer and let me tell you that bad boy cuts smooth now!! above all else don't give up. Before tearing anything apart though have a good strong look at your technique making sure to transfer all pressure to the outfeed table as quickly as possible with the stock. Hope this helps keep us informed. Quote
Godet Posted October 11, 2010 Author Report Posted October 11, 2010 I wouldn't go as far as to say your outfeed table is lower. It might be the table is sagging though. You wouldn't think it's possible in anything but wet particle board and older women but it happens. Like Marc recommends in his video pick yourself up the lee valley aluminum straight edge(longer the better) and get out your feeler gauges. clamp that straight edge to the outfeed table and measure the fore and aft section on the infeed table. I had similar problems and ended up shimming the outfeed table to be coplaner. I'm using an older Ridgid jointer and let me tell you that bad boy cuts smooth now!! above all else don't give up. Before tearing anything apart though have a good strong look at your technique making sure to transfer all pressure to the outfeed table as quickly as possible with the stock. Hope this helps keep us informed. Thanks...I got the instructions on how to make the tables co-planer from Jet today; they have a doc all set to email customers, which makes me wonder why they don't just send with the machine. I'm waiting for my quality strait-edge to arrive, but a quick look with my usual straight edges shows the outfeed table sagging. I waited a while to purchase this sucker and thought I did the research--must have missed the less-than-stellar reviews I've now found. Anyway, I'm determined to get it figured out. Quote
Godet Posted October 16, 2010 Author Report Posted October 16, 2010 Well, after receiving my fancy straight edge, A-Line It, and some feeler gauges in the mail this week, I tackled jointer again today. I'm happy to say I got it set. It took the better part of 5 hours to get the table set and to reset the blades, but I'm happy with the results. For anyone thinking about this machine--it's a kind of a pain to dial it in...but I'm still pysched about the price, and it does a good job. Quote
Godet Posted October 17, 2010 Author Report Posted October 17, 2010 Well, after receiving my fancy straight edge, A-Line It, and some feeler gauges in the mail this week, I tackled jointer again today. I'm happy to say I got it set. It took the better part of 5 hours to get the table set and to reset the blades, but I'm happy with the results. For anyone thinking about this machine--it's a kind of a pain to dial it in...but I'm still pysched about the price, and it does a good job. This machine is an emotional rollercoaster. After obtaining some good results yesterday, I moved today to actual projects boards, which are a good deal longer than the ones I tested yesterday. Results: 2 thumbs down! So, I went back to the drawing board (or straight edge, actually) and the out feed table was probably close to an 1/8 inch lower. So, back to the co-planer technique Jet sent...basically, you loosen two screws, pull the table into line, and tighten the screws. On my machine, the table stay co-planer until I fully tighten the screws. So, I started adding a few washers...this works, until you apply any pressure (like say, the weight of a board you'd like to joint), at which point, the table sags...and so too the corners of my mouth. Soooo, I have email in with my favorite Jet technician...unless he has some magic to offer (or any of you smart folks do), this sucker is going back...I'll save up until I can afford something more solid--probably go with a separate jointer and planer (wasn't psyched about feeding 3/4 inch stock into the planer blindly). Quote
Ben@FineWoodworking Posted October 17, 2010 Report Posted October 17, 2010 I have been interested in this machine for a few weeks now. Hmmm... might be more trouble than it's worth. The reviews on Amazon mentioned, basically, everyone having this problem but most being able to work it out. Some of them went into a lot of detail. You might wanna check them out. This machine is so attractive for the price. Please keep us updated. Quote
Guest Trace Posted October 19, 2010 Report Posted October 19, 2010 I have a Craftsman jointer. Not the top of the machine world, but it works for me. It is very easy to set dead on for the out feed table. It uses a fairly large wheel to turn the setting screw, which moves the table up or down. The infeed table is adjusted the same way. Both can be locked without disturbing the set. Some of the more expensive jointers are very nice and somewhat heavier in design, but harder to set up properly. Quote
Godet Posted October 19, 2010 Author Report Posted October 19, 2010 Trace: good to know...especially since I'm back on the market! Talked with Jet this morning and they recommended sending it back. After spending all weekend seeing what this machine is made of (not much) I'm not willing to take another chance. Even if one gets the tables set, there are only two screws holding it in place and the only play, is within the screw hole (not much). Frustrating weekend--I think I'm just going to save my money and go with something a bit nicer down the road...just have to keep borrowing my friend's machine for a bit. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.