Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

How long do you leave finishes in your spray gun?

Featured Replies

I'm going to start finishing a project today. Each round of spraying will last about a minute. I'm going to do 5 coats per side. Finish is lacquer. Do I need to empty the cup after each coat or can I let the finish sit in the cup for two days? What if I were to use water based poly?.

Adam

I do a full break down and clean after each day (sometimes even twice a day if there was a lot of spraying).  Never let finish sit overnight as it will clog the air or fluid ports giving a poor pattern on the next use.  If it's small amounts you're working with you could probably get away with only flushing the gun each night and save the full breakdown when everything is done.

My spray gun habits will make folks cringe, but I'll volunteer them in the name of science... :)

 

Important: In no-way do I condone these storage times... They are the poor habits of a lazy sod :) With a thoughtful selection of coatings, these storage times demonstrate just how far you can stretch the envelope -- and get away with it...

 

General: guns are kept filled for the duration of a project plus a day or so. If I'm shooting for two days, they are kept filled for about three days... If they're needed for a week, then they stay filled for a week or so... I don't waste time breaking-down/cleaning guns in the middle of a project. There are exceptions for fast-cure coatings, but I try to avoid them... My 'lazy man' workflow influences my selection of coatings -- I tend to use Mohawk's Industrial Coatings that have longer pot life than their consumer-oriented brethren. For example, their post-cat lacquer has a pot life of weeks, not hours. Their coatings are a bit more expensive, but it's worth it -- for me... I avoid fast-cat/cure coatings or coatings with a short pot life...

 

Note: Shoot 70:30 solvent to WB -- that is changing... I'll be 50:50 by the end of the year.

Note: Probably shoot 50gals of solvent-coatings this year (including shellac), maybe 10g WB.

Note: I'm using a disposables-based system (3M PPS) which helps a lot...

Note: I have several guns, which also helps a lot...

Note: dedicated guns for shellac, WB and solvent -- which helps a lot.

Note: I never use fast-cure/short-pot-life or pigmented coatings w/ a pressure pot... ever...

 

Note: If I shoot WB, I use a slow-cure Industrial WB... If I were to use fast-cure, I'd be replacing guns and/or production hoses on a weekly basis.

 

WB - same day cleanup -- usually... Sometimes next morning... I try to avoid fast-cure WB.

Solvent: cat lacquer/poly - day or three.

Solvent: slow cat lacquer/poly/etc - same day or three. Five days at the outside if I'm spraying every day.

Solvent: pre-cat - week or so... Sometimes longer if I've got a couple of projects in a row... Maybe two weeks, three at the outside.

Solvent: conv-varnish -- same day -- most of the time. Couple of days on the outside.

Shellac - perpetual... 2qt pressure pot. Maybe clean the gun every month or three.

NS Lacquer - same.

 

Despite deplorable maintenance, I've never had a gun clog, jam or fail. There have been two exceptions of note:

1) Gun fell into a five-gal pail of solvent-based metal etching paint --- without cup or air hose attached. Apollo recommended discarding the gun outright... Instead, it was immediately stripped, placed in an ultrasonic bath and rebuilt. Works fine...

2) Shot a pigmented cat lacquer sealer... The pigment stuck to everything -- the air chamber was a mess and it was a fast-cat coating... The gun had to be stripped and rebuilt. It was never quite the same. I vowed never again to shoot pigmented anything...

 

==>Never overnight in my spray guns. Many years of waterbourne finish use.

@OP:Steve's got a best practice maintenance approach... Emulate him, not a lazy sod like me...

You guys guilted me into it!  I emptied my gun tonight and broke it down for a good scrub.  The finish was in the gun for about a day and a bit.

I have a gun that I just use for spraying solvent based stains. It only gets cleaned ( quite thoroughly ) when I change stain colors.

I will admit to screwing up and leaving WB finish in a gun overnight. It makes it much harder to clean up and if it is late and I am dead tired I will dump the leftover finish, rinse the fluid passages, fill the gun and cup with water and clean it tomorrow. Only aluminum and stainless parts will tolerate this kind of carelessness. Trust me I have replaced chromed brass parts due to corrosion and abuse.

WB finishes can be corrosive , but my cleanup solvent comes out of the faucet !

You have to give HHH credit for being honest! You can take risks but be prepared to pay the price when it all goes south !

==>stainless parts

Steve's spot-on. If you can, avoid guns with brass/aluminum/etc... Yea, guns made from SS, PTFE, duralon, et al are more expensive, but they last a lot longer... One tip, before putting a gun into service, passivate the internals -- makes a big difference for long-term life: http://www.theruststore.com/CitriSurf-C64.aspx?UserID=33237632&SessionID=YyKwpskUxOmuKf . Also use Apollo's gun lube... It's much better than the petroleum jellies most MFGs furnish.. Yea, it's $8, but a little goes a long way: http://www.thefinishingstore.com/products/Spray-Gun-Lube.html ... Also avoid any guns with anti-stick 'coatings' -- these break-down over time and gunk everything up... Works great for a while, but not after they break-down.

 

==>being honest!

Figure the data may be useful to someone... Steve brings-up a good point. If you're going to abuse your spray guns, you've got to be willing buy rebuild kits (about a quarter the cost of a new gun). About once a year, I strip my guns, sonic-bath them, passivate the guts, and rebuild the seats/seals. It's either that or purchase disposable guns from HF: http://www.harborfreight.com/air-tools/paint.html. I don't run pigments through my pressure pot or guns... But I like pigmented sealers --- they save so much time -- so If I going down that particular path on a project, I just get an el-cheapo HF and toss it when the project is done...

 

The only other piece of advice is to know your coatings -- especially the working times... Read the technical data sheets -- especially on post-cat and WB coatings... The pot life varies from several hours to several weeks. A great deal of why I get away with what I do is by avoiding finishes that set-up quickly... Note: I'm talking pot-life, not dry-time... The dry-time for a coating can be 45 minutes, but it's pot life can be 45minutes to 45days...

 

A disposables system is key... When I used a cup, I couldn't be so cavalier... The PPS system forces air from the circuit which inhibits curing in the air-chamber... Doesn't stop it, just slows it down... BTW: I written on this before, but it's worth repeating. If you shoot any real volume, the PPS system pays for itself very quickly. Prior to PSS, I used to get a pallet-load of solvent delivered every few months -- maybe 50gals at a time... With PPS, my solvent use has plummeted by at least 75%... Clean-up is also a snap...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.