Recommended Posts

Posted

All these various chests inspired me to build my own. Thanks guys.

This is my starting point and we will see how it evolves.

http://www.finewoodworking.com/woodworking-plans/article/blanket-chest-by-hand.aspx

Started by milling a couple boards from my stash of cherry.

Edge cleanup with the LN LA Jack

a5ava7ug.jpg

Either the front or back panel glued up and in clamps. Not sure which it is yet....

ede6u7a9.jpg

Clamps off and squeeze out removed.

gyqadeta.jpg

Hope to get another panel or two glued up tomorrow.

My joiner does not like this cherry. It has some figure to it and it tears out like crazy. My planer is cleaning it up nicely though.

Posted

3y8aryby.jpg

Got the first panel smoothed out. Cleaned up the glue lines.

9aheru5u.jpg

The 3 other panels are glued up as well.

Not sure how I like my board alignment. I always second guess myself trying make them look good.

I have few boards partially milled for the top but don't think I will use them. Going to wait and do the top last. Need to look through the pile and find a couple Great boards for the top.

Get these glue lines cleaned up and I will be ready for dovetails.

Posted

It was a bit of a process this week to get anything done. Ended up building a big cross cut sled, didn't have a way to accurately cross cut panels on the new table saw.

Got the all panels cut to size. Glue lines smoothed out.

Ready to lay out the joinery.

mumy5apa.jpg

Posted

Made some progress since the last post. Joinery all laid out.

Cutting pins with my improvised vise. My workbench stinks. Need to add that to the project list. It is heavy though so as long I can figure out a way to hold the work piece I am good.

tyqeteru.jpg

I cut all the pins, which was a nice arm workout.

First set cleaned up, 3 more to go.

busuhade.jpg

Posted

Just realized that I screwed up the layout of the pins on this corner, it was the only one I messed up.  Lesson....quadruple check your layout!  Not terribly upset, did this side first because the knot I was trying to incorporate was a little more gnarly than I thought.  

 

I will just make a new panel for this side.

 

Live and Learn!!!  On to the next mistake!

Posted

Josh, maybe you should look into a moxon vise. I don't have one…YET. But for the price, it would be a nice addition for your bench it looks like.

 

You can even look into making your own hardware. I have seen a couple people go that route.

Posted

Decided to just cut off the pins I laid out wrong and just adjust the size of the chest.

Got all the pins done today. Working on laying out the tails.

Also trying to visualize how this mitre at the bottom corners needs to be cut.

bagyryre.jpg

Posted

Wanted to use two wide boards for the top. Made a quick and easy sled for my planer.

vuhyvu4u.jpg

Partially milled pieces for the top.

haty2u9u.jpg

Later today going to clean up tails and make up a sample joint to practice the mitered corners.

Posted

Wife and kids are gone today so getting some shop time.

Chopped the tails still have to fine tune. But can't do that until I get the mitered corners done.

jyty5a7y.jpg

A few pics of my progress.

y3avypan.jpg

e9u7ymud.jpg

yje5uzu7.jpg

Here is the test joint I made to figure out how to cut these miters. One side can easily be cut on the table saw. The other is a little more tricky.

Still not confident how these are going turn out. I hate miters!

yvu2y7ej.jpg

Posted

Alright think I am done for the day. Got a lot done but I am tired. Got the bottom laid out and cut. 1/2" material I resawed on my bandsaw. Think I have the tongue and groove and shiplapped joinery figured out.

I used leftover off cuts for the bottom. It all matched pretty well except that far board. It looks worse in the picture than it really is. It has some crazy grain. Cant see using more material for part that will never been seen.

jeqepy9e.jpg

Holding off cutting those miters until I think about it some more.

I would like some opinions on the top. Not thrilled with the look of the cleats but need something to help hold it flat. Maybe I just don't want to cut that dovetail socket! I could do breadboard ends, not sure how that would look? Thoughts?

Planning to put some nice strap hinges on it!

Posted (edited)

So if I go with breadboard ends here is what I have on hand. I could make them out of Cherry, Mahogany, or Walnut. Leaning towards the walnut but once the cherry ages it might look good with the dark brown/red mahogany.

Edited by JoshC1501

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 48 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined