Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Titebond 3 on finished surface

Featured Replies

Hello!

 

I've been trying to find an answer to this all day... I have some dewaxed shellac that dripped/ran into some joints, and I was wondering if it will really cause problems... I am building a baltic birch vertical cabinet, and the corners are Dado/Rabbet joints, with a couple shelves in the middle that are simply dado's. (Sorry newbie terminology)

 

Shellac is dewaxed flakes mixed to a #1 cut with 2 coats.

 

Should I worry about it, or do I start sanding and scraping it out?

 

Thanks!

post-15852-0-35231200-1405134941_thumb.j

You will have issues if there's glue where you want finish.  

Why did it drip into those joints? Did you coat the whole piece? If so, and the drips are not an unsightly bulge, I cannot see a huge issue. If you did not coat the whole piece, then you could conceivably have a difference show with whatever goes over the top. Was that easy to follow?

Wow, did I read that wrong...  Thanks C!

No Kev, now I am confused. I read the post, you read the thread title. To the OP, are we talking shellac, or TB III?

Are you asking if TB III will bond to shellac? Is the pic a dry fit?

I think you had the correct response C..

 

If you're concerned about glue sticking to a little finish in the joints, you're probably fine.  You should try to prevent that in the future.  If you're trying to put finish over glue, that never works.

  • Author

Pic is old. Dry fit before sanding. Just wanted to show joints in question.

To make it easier to apply shellac, I figured I would sand and apply before glue-up. Being a newbie I got shellac-crazy and started applying, not thinking straight.

I will try and wipe off.

Thanks for replies! Greatly appreciated!

BTW, welcome to the forum! I am not done making mistakes. Not to depress anyone but just as support that it is not just newbies:-)

  • Author

Nice! Thanks for the welcome!

Just to add more details to the finish to get your opinions...

Applied 2 coats of #1 cut dewaxed shellac to seal the birch.

Adding 10% General Finishes Amber dye stain into some General Finishes High Performance (both water based) to slightly tint the wood.

Was thinking of applying another coat of shellac to seal dye, then add more coats of clear (no dye) High Performance until I'm happy with the finish.

Any suggestions?

Thanks again!

Sounds like a good plan. Wipe with alcohol maybe a light sand then glue it up. Your finish plan should work fine.

If I am pre finishing before assembly I tape off the glue surfaces to keep them clean.

  • Author

Update.

 

Glue up didn't go so well.

 

Glue dried too quick for me to get the clamps on and align all the joints correctly. Almost every joint is slightly skewed. Tried to beat them straight with a mallet, but no go.

 

Now I get to try and fix it. - I assume I can use a hand plane to knock down the high spots and to bring everything back together?

 

I will post pics tomorrow once the glue finishes curing.

 

Have a great day!

Cory

Skew or wracking are your enemies here. Based on your pic: if one shelf is forward by an eighth on the left but backward by an eighth on the right then your shelf is not fully seated in the dado and the whole piece will be out of square. If one shelf is forward by an eighth on both ends, you may still be square. To take a plane to the front of the shelf and the back of the frame will reduce your overall dimension but will not hurt. In fact this is common practice in many fine shops because many of us will have a board swell a touch with glue moisture or will be off by the barest fraction. That plane will take all the shadow lines away and keep your fingers from feeling the catch. Let us know how it goes.

Edit: That appears to be ply. Edge planing ply is often tricky...

Just a thought to consider in future projects where you think your glue will cure to quickly, try to do sub sections.  So, in the case of this shelf, you could have done the top and bottom to the sides and clamped/squared and let it dry.  Then come back and put the shelves in.

 

I find I have to do this a lot especially in summer months.

I try to do complex glue ups during the summer months very early in the day before the temperatures rise. I also do sub sections. Clamping a few joints and come back in an hour to do some more.

Clamping up a dry run is always a good idea so you have everything already before you apply any glue .

  • Author

Yeah I never thought of gluing up in sections. Could have done 2 shelves at a time, then done the top and bottom. Damn!

 

Each shelf seems to be shifted side to side. - Except for one! lol. Maximum shift seems to be barely 1/16". Most are half that.

 

I have an old hand plane that I could use... Might just use 80grit paper on a palm sander to knock it down. Just have to be careful to avoid humps and valleys. 

 

Going to break from it today and focus on R&R.

 

Have a good day!

Cory

I have clamped wood blocks on either side of a protruding misaligned joint and then sanded it down flush. Plywood can tear easily with a plane. Sometimes I have used coarse sandpaper glued to a flat board to take it down close then a finer grit to smooth things out so I can glue on a faceplate .

Yeah I never thought of gluing up in sections. Could have done 2 shelves at a time, then done the top and bottom. Damn!

 

Each shelf seems to be shifted side to side. - Except for one! lol. Maximum shift seems to be barely 1/16". Most are half that.

 

I have an old hand plane that I could use... Might just use 80grit paper on a palm sander to knock it down. Just have to be careful to avoid humps and valleys. 

 

Going to break from it today and focus on R&R.

 

Have a good day!

Cory

 

Lesson learned, also called wisdom  ;) Unfortunately, without consequences there is not learning..

 

I haven't tried Steve's method but, sounds like a solid plan!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.