Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Is this a good buy for my 1st thickness planer?

Featured Replies

  • Author

So apparently the drive side of the carriage is raised and lowered by this little cracked thing I'm gonna call a "threaded lift lug"

post-6956-14091003003936_thumb.jpg

The "threaded lift lug" is held in place by

this broken "hold down machine screw" which snapped off inside the carriage top.

post-6956-14091004202712_thumb.jpg

What you see there is the broken screw head and the rest of the screw still sitting in the carriage body. Luckily I was able to file some little cross hairs Ito the screw and drill a small hole about 3/16" down into it. Tomorrow I'll go pick up a tiny easy out and order the parts.

I have 30 days to find out if this thing will get back to tip top shape. If it's still junk after 30 days H-Dizzle will take it back.

Unless there is a need for the part to be cast, I would think a machine shop could mill the part for the cost of a steak and some drink.

  • Author

You're probably right and I would do that if the parts weren't dirt cheap. The subtotal was $2.62 before shipping and in stock!

post-6956-14091023203821_thumb.jpg

  • Author

So I had bought some easy outs and tried to pull the shank of the set screw out of the carriage the other night. Well, the tip of the easy out broke off into the screw shank. Go figure...

Luckily the piece does not need to sit in one direction to perform properly. So I eyeballed a new screw hole right. Next to the former and drilled away. Once I tapped new threads into the hole the new set screw fit perfect. Only now the lifting lug is turned about 10 degrees or so towards the front. I had to trim the edge of a little dust cover but everything worked perfect.

  • Author

I don't have any precision measuring tools. But it seemed that a 8" board planned was about 1/64" thinner on one end.

I couldn't find any fine adjustments on the machine, so I removed the sprocket from one side of the lift and turned it by one tooth until everything seemed level. To judge the level of the cut I ran two 1" boards through on each far left and right side of the planer and judged the difference of their thickness. I had to jump about 4 teeth on the sprocket until I got a likeness I was happy with.

post-6956-14093748136202_thumb.jpg

The one one the right "might" still be a hair thicker. But the difference is negligible in my book.

  • Author

This thing planes a pretty good surface as long as I'm cutting a 1/32" or less on harder woods. Anything more and you can feel dips and hills in the board. There is also some very faint stripes that appear across the planes surface on harder woods. They seem fairly consistent so I don't know if it's the cutter blade that need to be upgraded or if they are just dirty? But it's nothing that isn't easily sanded. You can see them but not even feel them.

A piece of curly maple scrap:

post-6956-14093751030134_thumb.jpg

  • Author

All in all I have about $110 bucks into this machine. I'd say it was a steal!

I could probably sell it right now for $250. But I think I'll hang on to it for a bit. It seems it will serve my purposes.

Congrats!  Glad it worked out for you!

  • Author

Poor man got poor mans ways.

I'm thinking about making a series of YouTube videos about how to tune shop machines fo po folks!

Nice find!  I was going to muddy the waters with a suggestion for the DW 735, but since this is working for you, I'd say just run with it!

  • Author

We'll the Dewalt was on my list of wants. But this was hard to pass up. I can use this for a year or two and still sell it for double what I got in it. That's a win!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.