Recommended Posts

Posted

I've been thinking about doing concrete counters in my kitchen and/or bathroom. From some of the ones I've seen around the web, they can really look nice. Have any of you had experience first hand with a concrete countertop?

Posted

I've been thinking about doing concrete counters in my kitchen and/or bathroom. From some of the ones I've seen around the web, they can really look nice. Have any of you had experience first hand with a concrete countertop?

 

I don't have them but can tell you not to just flop them down on standard cabinets. We do some cabinets spec'ed for concrete and you need to beef up the cabinet in certain areas.

Posted

I don't have them but can tell you not to just flop them down on standard cabinets. We do some cabinets spec'ed for concrete and you need to beef up the cabinet in certain areas.

What are some key areas to look at?
Posted

What are some key areas to look at?

 

Sides and back need to be 3/4" ply. Toe kick need to be separate frames no levelers. Frame should have braces under partition walls not just outer edge. Wall mating needs double 3/4" ledgers. Wide spans need steel reinforcement (think dishwasher). Best to go with single custom cabinets rather than 3x boxes. Thicker counters need double outer wall along with double ledgers. Some designer will add double partition walls if the counters are thick.

Posted

Cabinets have to be engineered so that the counter top does not crack, it doesn't matter if it concrete or natural stone. There is more to cabinets than people think. There is a reason why spans are what they are. There is more to it than just sticking a counter on any old cabinet. When we supply builders with a single row of replacement cabinets 9 times out of 10 its because they didn't spec the cabinets properly or did not install them properly and the counter top cracked.

Posted

Cabinets have to be engineered so that the counter top does not crack, it doesn't matter if it concrete or natural stone. There is more to cabinets than people think. There is a reason why spans are what they are. There is more to it than just sticking a counter on any old cabinet. When we supply builders with a single row of replacement cabinets 9 times out of 10 its because they didn't spec the cabinets properly or did not install them properly and the counter top cracked.

I'm all for increasing the strength of my cabinets if I decide to go this route. However, I have to weigh the option of just building new cabinets as well.

 

Can you tell me the common measurements of cabinets? I bought a fridge that I thought was on the smaller side to begin with, but it sticks out about 8-10" from the edge of the counter top.

Posted

We have concrete counters in our stone garden kitchen. They are supported by mortar and stone that have stainless steel cabinets as inserts. The installer put rebar and angle steel as supports around the inserts to carry the load of formed in place counter tops. He made boxes to form the counters then put a piece of meliame on as the top. Then sealed it up and used hydraulic jacks to apply pressure. When he got what he called soup coming out the seams he stopped jacking. The finished counters are smooth as polished stone. He did spend an afternoon wet sanding them. He did have to come back and re-sand one that developed a dip and held water on it. I also most forgot the bottoms part of the counters were made from styrofoam.  

Posted

I'm all for increasing the strength of my cabinets if I decide to go this route. However, I have to weigh the option of just building new cabinets as well.

 

Can you tell me the common measurements of cabinets? I bought a fridge that I thought was on the smaller side to begin with, but it sticks out about 8-10" from the edge of the counter top.

 

Most of the time your base cabs are 24" deep by 34.5 tall plus the counter top making them 36. Widths vary but usually run in 3" increments. 

Posted

unless you buy a counter depth fridge, which is usually a lot more money, it is going to stick out. That is why so many kitchens have a fridge box cabinet that is deeper than the rest with two doors above the fridge.

 

Good point. I forgot about about the "nook" the fridge sits in at my fiance's parent's house. I thought that just because my cabinets were old, maybe they weren't as deep back then. 

 

Most of the time your base cabs are 24" deep by 34.5 tall plus the counter top making them 36. Widths vary but usually run in 3" increments. 

 

Thanks for the measurements. Looks like my cabinets are pretty darn standard. Might have to think of something interesting if I ever decide to gut the kitchen and start anew.

 

I have about 14-16 linear feet of uppers and lowers in my kitchen, shaped in a L, whereas both lengths are equal. Think of it as only 2 sides of a square. 

 

If you guys had the below kitchen layout (rough scale drawing of mine), what options do you think would be the best in terms of appliance placement? Given, you could put them anywhere. I know it comes down to what I think would work best in MY kitchen, but it always helps me to influence ideas given other opinions.

 

kitchen_zpsc3dc9fd0.jpeg

Posted

Go to a design center or even home depot and have them do a few full scale layouts for you. Some places will do it for free if they are slow, some will charge a little. Go home with the design and build them yourself.

Posted

looks good overall. personally i would move the fridge all the way to the end to keep the counter uninterrupted. I cook a lot and I really like lots of continuous counter space for prep work. That little two foot (or whatever it is) to the left of the fridge will just be a magnet for crap.

 

I like that idea of moving the fridge down. That little bit of counter space to the left does just that, collect junk.

 

Go to a design center or even home depot and have them do a few full scale layouts for you. Some places will do it for free if they are slow, some will charge a little. Go home with the design and build them yourself.

 

Might be a good option if I can get it for cheap or free. I like having other eyes for things like design.

Posted

Every designer and cabinet maker including myself uses 2020, its very expensive. It takes our catalogs and pretty much any manufacturers catalog and places renderings in 3d. You can get access to generic catalogs many places, all our catalogs are only sold to designers. You can access a online simplified version of 2020 at many places with generic catalogs. Try going to lowes.2020.net this should backdoor you right into their simplified designer.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 36 Guests (See full list)

  • Forum Statistics

    32k
    Total Topics
    437.5k
    Total Posts
  • Member Statistics

    26,007
    Total Members
    3,644
    Most Online
    FurniCore
    Newest Member
    FurniCore
    Joined