Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Insulating garage shop

Featured Replies

Ok I'm insulating my new garage for a shop I'm using blow in insulation. I live in Illinois and there is two menards deals I can get r-30 for 20.00$ or r-19 for 5.50$ this will be in the walls. I know you can use a lower r value for walls I just don't know if r-19 is high enough. Should I get the r-19 or the r-30? Will I regret spending less?

I would think the R value for blown in would be based on the thickness not the brand.  For example if you have 4 inch walls, the R value is going to be basically the same regardless of which brand you use.

I think Mark is correct.  However, the standard for walls is R19.  You are always better to have more.

The only true way to get better than 19 in 4" stud walls is with spray foam. This is not a big deal if you can effectively seal against air infiltration. Air leaking through is the big enemy of the minimally insulated building.

Putting R-30 in a four inch wall will over compress it and defeat its usefulness.

The only true way to get better than 19 in 4" stud walls is with spray foam. This is not a big deal if you can effectively seal against air infiltration. Air leaking through is the big enemy of the minimally insulated building.

Putting R-30 in a four inch wall will over compress it and defeat its usefulness.

With polyisocyanurate  sheets you can achieve R-19.5 while still maintaining a 1/2" air space in a standard 2x4 exterior wall. 

  • Author

awesome guys im happy to hear that rather spend 530$ I will only have to spend 230$ ill spend the extra money ony wood for my lathe bench and table saw outfeed table

ill spend the extra money ony wood for my lathe bench and table saw outfeed table

 

...and bulk CA glue. =p

With polyisocyanurate sheets you can achieve R-19.5 while still maintaining a 1/2" air space in a standard 2x4 exterior wall.

This is not a standard application for PIR. It is a PITA to try to install this in residential stud bays with window headers, irregular opening cripples, and wire or plumbing. PIR is more standard as a wall hung exterior treatment around here. Do you install this in stud bays?

This is not a standard application for PIR. It is a PITA to try to install this in residential stud bays with window headers, irregular opening cripples, and wire or plumbing. PIR is more standard as a wall hung exterior treatment around here. Do you install this in stud bays?

Yes, i have installed this product on many jobs as requested by my boss. A pita, yes indeed, but in moisture and flood prone areas this stuff doesnt absorb the water like fiberglass batts.

Understood. It is after all a closed cell foam in board form. We wrap houses in it, foil tape the seams, and then cap the bottom edges against critter incursion before some reside jobs. Less with advent of affordable house wraps. I will not say it is a bad product.

We are having foam put into the blacks of our garage and the attic surfaces. It smells like chemical waste dump as it cures but I did notice a difference just with the blocks being filled. Last night was much colder and I found myself working in short sleeves. They also put precut foam onto the insides of the garage doors. They drilled a hole for the foam into each block. Then they put a camera into the cavity to look around then they put the foam in and it expands to filled space. They then do the next 4-5 spaces then trim tops flush. The vacuumed up everything and plugged all the holes. The walls are R-32 and the roof R-40. The roof is getting two layers.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.