chefmagnus@grics.net Posted November 5, 2014 Report Posted November 5, 2014 I spent today trying to find out why the blade on my Unisaw would not go up or down. I tried everything. Thought might have a piece of wood jamming the blade or something. I get good boy points for shutting the breaker off and locking the box with the key in my pocket. I then looked around and could not find anything wrong. Decided that something was seriously wrong and decided to take the top off. I spent almost 4 hours fighting with the bolts to get the top off. Then with my wife's help we sat it off to on side. Here is the sight that not a lot of people get to see. The underside of a Unisaw table top... Got into the guts of the saw. Tried to turn the rod to raise the blade and it worked. Really confused now. Got out of the saw and walked around front and tried turning the knob again. Nothing! I decided to try it again. This time the handle came completely off into my hand as my jaw dropped. Looking closer at the handle I find that it is stripped to the point that the hex key is gone. Realization that I did not need to take the top off the saw caused eruption of cussing and cursing. I googled handles for Unisaw Now that I have the saw opened up, I will take the time to lube everything up. and maybe change the belts to linkbelts. The belts look good but I would rather be safe than sorry. Can anyone make out the model number? It looks like it is double stamped. How would I tell if it is wired for 230V or 460V Also I hate the smell of spray foam. I hope that they finish installing it tomorrow Quote
chefmagnus@grics.net Posted November 5, 2014 Author Report Posted November 5, 2014 I googled Unisaw Hand wheels and got thousands of results. Has one dealt with a good older saw restoration company? I tried calling Delta and got put on hold for 17 minutes then called back and they had there phones on voice mail for the night. The place for the missing hex key is cracked on the height adjustment and the angle adjustment is going to fail at some point. It has visible cracks around the hex key. Thr rods turn smooth. I wonder what would stress out the hand wheels. Quote
wdwerker Posted November 5, 2014 Report Posted November 5, 2014 http://www.sawcenter.com/unisawparts.htm The belts need to be a matched set, Quote
wtnhighlander Posted November 5, 2014 Report Posted November 5, 2014 Open the motor terminal box, there should be a wiring diagram inside to show the connections for 230 or 460 volts. Quote
Tom Cancelleri Posted November 5, 2014 Report Posted November 5, 2014 If you're gonna buy new belts, I recommend cogged v-belts from goodyear. They're inexpensive to replace all 3 and cogged belts run smoother than standard belts as they are more flexible and cool better during use. I believe this is the correct belt for a Unisaw. 26" outside length, 1/2" width and 5/16" thickness. I'm running the 25" belts on my Jet cabinet saw and they made a noticeable difference, not only in less vibration when running, quieter, smoother shutdown of the machine without that belt flap and chatter that you get with older belts. http://www.amazon.com/dp/B004ELAD8U/ Quote
Tom Cancelleri Posted November 5, 2014 Report Posted November 5, 2014 If you have the 5" motor pulleys you need a different size belt then the one I posted above Quote
chefmagnus@grics.net Posted November 6, 2014 Author Report Posted November 6, 2014 Thanks for the heads up. I was about to just order them. I will measure the pulley and the belts. I already took them off and pulled the motor because I could not see into it with it mounted because of my poor eyes... I have started doing a full rehab on this saw. It looks good and clean but the handwheels condition makes me want to check everything out. I hope to get even years out of it until the UniLightSabre comes out. Quote
chefmagnus@grics.net Posted November 6, 2014 Author Report Posted November 6, 2014 The rehab website says that you need to replace the arbor bearing. These feel smooth. Would you go a head and replace them or just leave them alone? Quote
Tom Cancelleri Posted November 6, 2014 Report Posted November 6, 2014 I just finished up restoring a 12 year old Jet JTAS 10LX that was sitting in a damp garage accumulating rust, I liberated it from the guy who owned it for $500 bucks. I there was rust on the pulleys under where the belts were sitting, I took the cast iron top off, soaked it in evaporust, since i don't have a pulley puller I couldn't get the pull off the motor, so I removed the belts, grabbed a brass wire brush and turned the motor on and pressed the wire brush against the spinning pulley. Worked like a charm. I cleaned the hand wheels with wd40 and 0000 steel wool. I was concerned the top was horribly pitted, however I lucked out and it was all surface rust. I must say Evaporust is some amazing stuff. I do plan on stoning the top to clean up some of the carbon staining, but after 25 hours of work cleaning the saw up and getting all rust and polishing it up. Building a new extension table (debating on whether I want to put the xacta router lift in the new extension or not) anyway back to restoration. I didn't think the arbor bearings needed to be changed, however if they are smooth and aren't making any noises I would leave well enough alone. If you have a dial indicator I'd check the arbor for runout and make sure that it's within acceptable tolerances. Make sure to clean and lube the trunnion, use a dry lubricant. Enjoy your restoration, it's always fun to see how good of a job you do after hours and hours of labor. The first cut is always the sweetest Quote
chefmagnus@grics.net Posted November 6, 2014 Author Report Posted November 6, 2014 Also would you repaint the cabinet and rails? Not a crazy new color just get it back to new. It has been painted twice before. There are layers of gray, white, CAt yellow, then grey. My father in law made a call to Caterpillar archives and was able to get them to send me a copy of the purchase order for the saw. It was purchase in 1974 for building SS. There was also a record of sale to Paul in 1985. I will have the saw almost fully pulled apart by this evening. I can put the cabinet in the van and take it to get painted in CU. I did a wedding reception for the guy and can call in a favor. They do 20-30 cars a day and have a huge shop. Personally I would like to see it show room new but don't want to commit an act of taboo... Quote
Tom Cancelleri Posted November 6, 2014 Report Posted November 6, 2014 I would paint it for sure. If you're gonna go through all that work to restore it, you may as well make it pretty. I wax my cast iron tops and wipe down my cabinets more than I polish my furniture. I contemplated having my cast iron top resurfaced at a machine shop. Sadly, most of the machinists my dad used to work with have passed away, and he has no more connections in the machine shop. Quote
chefmagnus@grics.net Posted November 6, 2014 Author Report Posted November 6, 2014 If the top is flat and no rust, is there any reason to get it resurfaced? Quote
Tom Cancelleri Posted November 6, 2014 Report Posted November 6, 2014 If the top is flat and no rust, is there any reason to get it resurfaced? OCD and my obsession for shiny things in my shop. Quote
wdwerker Posted November 7, 2014 Report Posted November 7, 2014 Oh hell no ! If it is flat leave it alone ! Buff and polish if you must but machine a flat top ? Sacrilege ! If you must paint some version of battleship grey is appropriate . Or hot rod themed with flames could be fun? Damn , gotta watch posting after a few cocktails ! 1 Quote
chefmagnus@grics.net Posted November 7, 2014 Author Report Posted November 7, 2014 My autobody millionaire contact says that he is going to have his kids make up some examples of what they can do. I catered his kids weddings and he says he owes me a favor. So I am going to let him show me what they can do. I am going hunting with the kid on Saturday and Sunday. We are staying at the cabin over night. It is less than an hour to his shop. We are going to take the frame down then. They are going to 3D scan it and make sample paint schemes for it. I am leaning towards a restoration. Quote
Tom Cancelleri Posted November 7, 2014 Report Posted November 7, 2014 You should get a 3D Delta logo airbrushed on the cabinet Quote
wdwerker Posted November 7, 2014 Report Posted November 7, 2014 Kids who grew up with an auto paint shop? Let them go wild ! A pinstriped multi color UniSaw would not be boring ! Quote
wtnhighlander Posted November 7, 2014 Report Posted November 7, 2014 Von Dutch all the way, baby! Quote
chefmagnus@grics.net Posted November 8, 2014 Author Report Posted November 8, 2014 They emailed me a couple of ideas today. No pictures just their thoughts. 1)Phoenix in flight on a sawblade sun. Taking off from a nest of rusted and broken shop tools. 2)Doll Up pinstripes in the shape of a large number "1" 3)As close to factory as they can. 4)A rabid zombie beaver. 5)Flames and skulls. They said that they would have some pictures next week. They were busy finishing up things today. We will drop off the frame/shell tomorrow after a morning of hunting. I don't know if the "Kids" will be there in the morning. I will think about all of these. If you like one better than the others please let me know and why? Quote
wtnhighlander Posted November 8, 2014 Report Posted November 8, 2014 My opinions, with rankings: Phoenix rising: most original and artistic. Flames and skulls: most classic pimp-out Factory original: Most classy. Big number one: most folks won't get it. Zombie beaver: Meh, funny but I am not a zombie fan. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.