Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

The 2014 xmas build hourly thread

Featured Replies

So having cleared the easel out the way i thought i would try and make the Jewellery box that Marc made for my gf for xmas.

 

And i thought i would run with Chets hourly update log to give me a push to get it done in time for xmas :). Everything done with hand tools again.

 

So here goes

 

Hr 1, all parts laid out and cut, scrub plane sharpened.

 

15174031554_06c8ce919e.jpg

 

Hr 2, Both breadboard blanks and 1 side piece rough planed, both faces on the 2nd side planed.

 

15608820207_26225e4ec4.jpg

 

You will notice i have moved my bench from the centre of the floor to the back wall. I have so much more space now, breaking down the board was so much easier. And best of all i no longer keep nutting my wood rack when I'm cross cutting :)

 

Time for a spot of lunch and then i have to clean the fish out. Hoping to get all the parts rough planed today so they can sit and adjust.

  • Replies 60
  • Views 13.3k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Hour 7 and i have the box frame at final length and width.   They still need to be re flattened a tad as they have cupped a little over night, should only be a couple of passes.  

  • No work on the box tonight.   But i have just ordered some Katazome paper for the bottom  

  • Marc made your girlfriend a jewelry box for Christmas?

I'm looking forward to it as well.. As long as we don't see those hourly numbers Eric is tossing about...  ;)

. And best of all i no longer keep nutting my wood rack when I'm cross cutting :)

 

 

 

A general workshop hazard cracking ones bonce on the timber storage receptacle.

  • Author

Hour 3 resulted in all the parts rough milled with the exception of the 2nd top. 5 mins later that was done. I also re sharpened the scrub plane and had to switch the heating on  :blink:

 

So all parts are sitting waiting to be properly surfaced tomorrow assuming they haven't moved too much on me.

 

15175098084_d3374f57a1.jpg

I really do like these hourly builds, I get a feeling of being there peeking over your shoulder.

I've always liked the way black walnut shavings look coming out of the plane. If you photograph them just right they remind me of the chocolate curls you get on top of a French Silk Pie. 

 

Great work with the scrub.

  • Author

Hour 4 was spent sorting out which faces would be presentation faces, sharpened the jack plane, established reference faces on side pieces, side one cut to width.

 

15183648313_9ea1407888.jpg

 

Hour 5, side 2 trimmed to width, front and back pieces also trimmed to width. Photo is the back having the cut edge squared up.

 

15779431836_1a183347d2.jpg

 

Hour 6, broke out the skew mitre plane and shot one end of all the box frame parts. Measured and marked the other ends and cut to length.

 

15183658433_5839093ef8.jpg

 

So at the end of day two I'm almost at the point of cutting joinery :) Just need to equalise all the pieces next

 

15183140704_3a4b896e14.jpg

  • Author

Hour 7 and i have the box frame at final length and width.

 

They still need to be re flattened a tad as they have cupped a little over night, should only be a couple of passes.

 

15193628573_1063670d1d.jpg

  • Author

No photo for hour 8 as i just thicknessed all the parts and cut some blanks to practice the joinery on.

 

We are now ready to cut joinery on the box :)

 

Not to jinx it, but its gone super smooth so far :)

  • Author

No work on the box tonight.

 

But i have just ordered some Katazome paper for the bottom

 

large-katazome-shi-130.jpg

So having cleared the easel out the way i thought i would try and make the Jewellery box that Marc made for my gf for xmas.

.

Marc made your girlfriend a jewelry box for Christmas?

Marc made your girlfriend a jewelry box for Christmas?

That's how I read it too. :)

This is how nasty rumors start... ;)   Hope Nichole isn't reading this.. :o

This is how nasty rumors start... ;) Hope Nichole isn't reading this.. :o

Uh oh. Someone's got some 'splaining to do ;)

  • Author

Ahem, missed a comma somewhere

  • Author

ok hour 9 was just a practice of the joinery

 

15834784122_316555cb48.jpg

 

Really tight but quite a few gaps. My sawing was off resulting in not straight faces but i only really wanted to practice the laying out side of things. 

  • Author

Hour ten saw the continuation of the joinery practice.

 

15834769795_eca412fdf4.jpg

 

And we have a completed test box. This thing is not coming apart.

 

This is the best face, you don't want to see the real state of it :) Hopefully thats all the mistakes out of the system now.

 

15649630737_b5607fec80.jpg

 

The paper and glue has arrived so im hoping to have the box glued up by the end of the weekend.

  • Author

Hour 11 consisted of layout and getting the first mortice cut

 

Unfortunately while flattening the bottom i snagged the corner some what and now theres a visible cut. Hoping it will be hidden by the tenon but i can always glue a chip in there.

15819952276_484a7d4360.jpg

 

Hour 12 and i have 4 mortises cut and 2 tenons marked up.

 

I am impressed with how these have come out. All 4 are exactly the same size, line them all up and i can't feel any ridges between the boards. Hopefully the tenons will go as smoothly. 

 

15226131463_efd13e8761.jpg

  • Author

Hour 13 and we have box :)

 

15663092138_e8bce7c934.jpg

 

Only one tenon was loose so i have the cheek gluing up and will re cut.

 

There will need top be a fair bit of tweaking to get them to close up flush to the base lines but i am very impressed with how it came out fresh from the saw.

 

15663253680_36887a5a4f.jpg

  • Author

Hour 14 spent tweaking the tenons fit. Realised i glued the cheek onto the wrong side of the tenon so had to re do. Waiting on that to set up then have another round of tweaking tomorrow.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.