Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

What kind of joint for this project?

Featured Replies

Hi.

I am building a table in slow motion. I'm nearing the point where I can glue up the legs and aprons so my thoughts are moving to the top.

My "design" calls for a table top that has 5" x 3/4" border, with the inner field of the table a (faux) leather insert (it's a table for family game night).

I expect I will put the "leather" on a plywood panel that floats in the middle of the frame made from the 5" wide boards described above. It will be like a leather picture in a wood picture frame

My question : what joint for the corners of the outer "frame" of this table top? I'm sure they will look best if mitered, but how? Some fancy mitered tenon? Perhaps a half lap joint, with or without a miter?

I post here as I'd prefer to do this with hand tools (although I have a table saw if I must).

Has anyone done anything like this? What might look good, be adequately strong, and reasonably likely I'd be able to pull it off?

I searched for something like this, but I did not find much.

In case it matters, I cut button mortises in the table aprons. That is how the top will attach to the legs.

Thanks in advance!

Matt.

Sent from my iPhone using Tapatalk

Have you considered adding a spline through the mitered joint? They add considerable strength, and there are numerous was to do them. If I were to tackle this with hand tools, I would either do mitered half laps ( a pain to get perfect), or do the plain miter and glue it up, the cut a wide groove on the back side of the joint, in line with the miter cut, i.e. 45* to the frame pieces. Glue a flat board into the groove, then trim to fit. Much easier than cutting a groove through the edge of the miter for a centered spline, although probably not quite as strong.

  • Author

I had not considered a spline on the back. Perhaps the fact that the top is clamped to the table frame will make it stronger still?

I gave brief thought to a spline through the corner - cut through the middle of the frame thickness, but discarded that idea quickly.

If I do a spline on the back, I'd want to run the grain perpendicular to the miter line, no?

Another thing that occurred to me, I suppose if I screwed up the miter, I could do inlay or a small spline over the miter on the top side.

Sent from my iPhone using Tapatalk

Sounds not dissimilar to what I did on my coffee table, a mitred frame with a removable game panel in the centre. It's held up well for the last five years.

 

I reinforced the mitres with loose tenons - This was only my second furniture project and was before I owned a whole lot of tools, however I used a router to make the mortices not hand tools as I would now.

 

Getting the mitred frame to close up tight on all four corners however was quite a challenge with the limited tools I had - as a result the central panel is slightly off square, and the game boards only fit properly one way round.

post-4067-0-33705200-1417453316_thumb.jp

post-4067-0-67456400-1417453325_thumb.jp

post-4067-0-08614200-1417453345_thumb.jp

  • Author

I reinforced the mitres with loose tenons - This was only my second furniture project and was before I owned a whole lot of tools, however I used a router to make the mortices not hand tools as I would now.

Woah. First off, that is awesome! I won't have the removable field that you have. Just a fixed center panel covered in leather to rest the games on.

What do you mean by "loose tenons"? Do you mean a biscuit or spline floating in a slot? I don't see evidence of a tenon, at least not a through tenon or half-lap on your table.

Sent from my iPhone using Tapatalk

What do you mean by "loose tenons"? Do you mean a biscuit or spline floating in a slot?

 

Pretty much. You make matching mortices on the inside of both sides of the mitre joint, then cut a piece of wood  to go in the hole bridging both mortices with the strong direction of the grain. With a 5 inch wide 4/4 frame you've got plenty of room to get a good sized piece of wood in there to give it lots of strength. Nothing will be visible on the outside.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.