Illini40 Posted December 30, 2014 Report Posted December 30, 2014 Hello, While I save up for a jointer, I have been watching numerous YouTube videos on jointing on a table saw or router. Any insight or guidance on either technique? It looks like methods on a table saw are pretty straight forward and easy. Any suggestions on material to use for a jig? 1/2" ply? Quote
..Kev Posted December 30, 2014 Report Posted December 30, 2014 I seen some of those videos but, never actually tried it as I have a router table. 3/4 would be better for that sort of jig in my opinion. Perhaps it's time to build a router table? Quote
dwacker Posted December 30, 2014 Report Posted December 30, 2014 Keep in mind you still need a flat face. Your going to be better off using the table saw and straight line ripping provided you can get a clean cut. Even if you have a jointer straight line ripping at the table saw is sometimes a good first step. With a router table you will need to have a almost straight board to begin with so your probably going to be better off setting up for both. 1 Quote
Illini40 Posted December 30, 2014 Author Report Posted December 30, 2014 I seen some of those videos but, never actually tried it as I have a router table. 3/4 would be better for that sort of jig in my opinion. Perhaps it's time to build a router table? Yes - I am planning on a router table. When you use your router table to edge joint, do you just adjust the second half of the fence out further, in line with the router bit?Keep in mind you still need a flat face. Your going to be better off using the table saw and straight line ripping provided you can get a clean cut. Even if you have a jointer straight line ripping at the table saw is sometimes a good first step. With a router table you will need to have a almost straight board to begin with so your probably going to be better off setting up for both. Yes - I realize I still need a flat face. I'm just looking for alternatives to edge jointing until I get a jointer. Can you expand on setting up for both? I assume you mean set up the table saw and router? If a make a jig to edge joint on the table saw, why would it be necessary to then go to the router table? Thanks! Quote
dwacker Posted December 30, 2014 Report Posted December 30, 2014 Yes - I realize I still need a flat face. I'm just looking for alternatives to edge jointing until I get a jointer. Can you expand on setting up for both? I assume you mean set up the table saw and router? If a make a jig to edge joint on the table saw, why would it be necessary to then go to the router table? Thanks! Your fence is not long enough to edge joint anything more than a very short board. If you straight line rip it first your just using the router to clean up the cut if needed. Quote
Dave H Posted December 30, 2014 Report Posted December 30, 2014 You can make your table saw jointing set up as complicated and expensive as you want. But mine is about as down and dirty as they come some OSB and a couple toggle clamps and about 15 min. works great for me. Quote
AceHoleInOne Posted December 30, 2014 Report Posted December 30, 2014 Stop woodworking till you have the funds to buy a jointer. You will be glad ya did. Just buy one, trust me, you will be using it a lot! -Ace- Quote
Illini40 Posted January 1, 2015 Author Report Posted January 1, 2015 For a table saw edge jointing jig, is the only part of the jig, that must be square, the bottom piece that rides against the fence? It looks like I would not need to worry about anything else on a simple sled jig, other than the one bottom piece that rides against the fence. Quote
wtnhighlander Posted January 1, 2015 Report Posted January 1, 2015 The edge of the sled that goes against the fence must be straight. Aside from that, the sled is pretty simple, just needs to hold the work piece securely. If you plan the clamping mechanism correctly, the sled can double as a tapering jig as well. Quote
dwacker Posted January 1, 2015 Report Posted January 1, 2015 If you just run down to Home Depot and buy a premade melamine shelf they make a great sled. Quote
Illini40 Posted January 1, 2015 Author Report Posted January 1, 2015 If you just run down to Home Depot and buy a premade melamine shelf they make a great sled. Great idea - thanks! I think I saw that Menards had them on sale. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.