Recommended Posts

Posted

I've been using my new Jet JPS-10TS for about 2 months now and it has been working great.  However, after using my stacked dado blade some cabinet dado's, it seems to make a 'screeching' sound on start up and appears to be vibrating a bit more than before (dont remember any vibration but could be in my head now that i hear that noise) with my regular blade as well. The dado blade was put on per instructions and was making a 1/4 inch depth at undersized 3/4 birch ply width and is a new frued 508 (i think?).

 

So far I cleaned out the dust from the inside of the cabinet, and blew off the belt grooves as best as i could as there was some dust wedged in some of them as i read it could be the belt slipping.  (I am running a 2HP Jet dust collector as an FYI)

 

The sound/vibration remains.  Besides potentially tightening the belt, I was going to call Jet and see if they could help but wanted to make sure it wasnt something easy to fix, or potentially a bigger issue others have run in to.

 

Thanks,

Ted

Posted

Sounds like a loose belt. If it was a new saw there is usually some belt stretching that will happen with use.

 

Ok that makes sense as it was a brand new saw and was going to be my next step anyways.  I'll tighten the belt tonight and hopefully that solves the problem.

 

Thanks

Posted

Ok that makes sense as it was a brand new saw and was going to be my next step anyways.  I'll tighten the belt tonight and hopefully that solves the problem.

 

Thanks

 

The vibration would be coming from the belt as well. when there is not enough tension on the belt it will flutter and cause vibration. I find single V-belts to be rigid and cause more vibration than they should. I replaced the V-belt on my JWTS-10 with a poly link belt which made it much smoother. 

Posted

So I tightened the belt (what a PITA) and the screech went away but now the vibration is worse...rhythmic pulsing every second or so.

Tried calling Jet customer service but 8am-5pm was limiting.

Will call tomorrow but this is very frustrating for a new saw.

Posted

So I tightened the belt (what a PITA) and the screech went away but now the vibration is worse...rhythmic pulsing every second or so.

Tried calling Jet customer service but 8am-5pm was limiting.

Will call tomorrow but this is very frustrating for a new saw.

 

Unplug your saw, take your arbor nut, flange and blade off. Run the saw and see if there is vibration. It's possible you overtightened the belt. Also check that the motor pulley and arbor pulley are co-planer with a straight edge. If they aren't co-planer that could introduce the vibration you're talking about. Also make sure the set screws on the pulleys are tight and the pulleys aren't wandering. You should be able to adjust the pulley to be co-planer by loosening the motor mount bolts and shifting the motor.

  • 10 months later...
Posted

So I fiiiiiiiinally got around to putting a v-link belt on after just suffering with the noise and it's still making the same screeching on start up. 

With no blade there is no sound like before.

i checked coplanerity as best I could contorting upside down...pulleys don't seem to be loose either.

any other ideas or am I back to calling customer service?

thanks, Ted

Posted

You've gone a year with this problem? I live close to NASA but don't work there, so take this with a grain of salt. But it sounds like a bearing to me, especially since it doesn't make the noise until you load it with a blade.

Posted

Yes...the saw cuts fine and square so really just a nuisance and was doing shop setup until August so that's my excuse!

i will call Jet and see what they say 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 39 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined