Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Is it needed?

Featured Replies

I have a 3hp grizzley dc. The farthest a tool is away is 15 foot away. I can do ducting all the way to all the tools. But is it realy necessary?

I did moving flex hose for years and it works but recently did spiral pipe ducting and love it. It was really easy to do and went pretty quickly. Here is a thread on mine:

  • Author

estesbubba. that looks realy nice. But my farthest tools is only 15 foot away.But Would running ducking up the wall, across the shop add blast gates then flex hosing at all the tools. Be benifical just to go 15 foot? The convince would be great. Not dragging the flex hosing from tool to tool.

>>>>The convince would be great. Not dragging the flex hosing from tool to tool. 
 

 

 

You just answered your own question. Consider it a good thing that you don't have far to run it. Less money to invest and better DC.

 

 

 

  • Author

4 inch hose. What I mean by benifical is would I lose Cfm using ducting over flex hose?

If u are running 4" hose u are already losing a lot of cfm. Can your collector handle a larger hose diameter at the impeller?

Flex hose had a lot more resitance than pipe.

Then go for it. Run a main 7" pipe across your shop, and then drop down from there.

I went from 4" to 5" and noticed a huge difference. Going from 4 to seven will be awesome!

Also, modify your machine ports to larger diametets if you can.

Straight pipe offers the least resistance, smaller sizes and elbows restrict the flow. I have seen charts that list the equivalents and limits. Some of this info should have come with your dust collector.

  • Author

Thanks guys. I'll go with 7" main run it across the shop and drop down at the tools

  • Author

I wasn't sure if doing the ductwork and spent the money would help that much. Since I'm so close to the tools.

It's a little complicated, and there are a lot of factors in DC. As long as u keep your cfm where it should be (a real 800 cfm) you will be okay. The issue with 4" full runs is that they are not capable of carrying enough cfm - pipe is too small in diameter.

I am close to my tools, and I use a 1.5hp collector with a 5" hose. I can only use a length of 6 feet or less of flex hose before I drop below the threshold and lose good, fine dust collection. Rigid pipe would allow me to go longer.

If you have 7" diameter, use it to your advantage. I would run 6" pipe if my inlet accepted it.

I also changed out the 4" ports to 5" on whatever machines I could.

  • Author

After I did some mesuring and calucations. To go with a run that would go to all the tools. This included every thing, fittings, pipe, Y etc.   Im looking at almost 3k. That is crazy to go 15 foot. Ill be sticking with the flex hose. Thanks for all the great advice.

Unless you have drops its not going to do much good. If your ports are all 4" then all your going to get is 450 cfm. Where it makes a difference is like with a wide planer where the chips are filling the pipe effectually reducing the size and cfm. Your other tools that just make dust like a table saw will not see much if any benefit. If your running a planer and not running wide boards like 12-20 your not going to back up the hose with just a 15ft flex hose run.

Im to lazy to swap hoses but if cost is an issue just use 4 or 5 inc pvc. I put mine in with cheap pipe from pen state and paid for a custom set up and it sucked the pipe flat the first time I used the collector. I got upset and swapped it all out for cheap pvc and really can't tell any difference and my shop stays very clean. The only time I have any issue is when I plane boards close to 20" wide one after another on high speed but I have drop on every machine and its quite a ways further than 15' with 4" pvc.

After I did some mesuring and calucations. To go with a run that would go to all the tools. This included every thing, fittings, pipe, Y etc.   Im looking at almost 3k. That is crazy to go 15 foot. Ill be sticking with the flex hose. Thanks for all the great advice.

Wow, 3K? Where did you price your materials? I did all mine for under $500 and that is all 6" spiral pipe, wyes, and blast gates. I got mine all locally, and since you're also in NE, you might want to check with them:

 

http://www.wsmind.com/wordpress/new-locations/

 

IMG_0390.JPG

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.