Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Staining only part of a surface

Featured Replies

I am thinking of building an electric bass guitar, but before I get started, I wanted to figure out some difficulties in the process.
I have a picture of the style I wanted to make attached.  

I would like to know how to go about staining the outer sections with a red stain without staining the middle sections.
I am not sure if masking the area with tape after assembly would be sufficient, or if I might have to Pre-Stain each piece before glue up, and what disadvantages that might bring.

I would also love suggestions on what timbers to use to get a similar grain pattern and base colour.

Thankyou!   

butcheredSB1000body.jpg

I would definitely do two glue ups. I would glue up the center pieces first. If you used maple and walnut they wouldn't need stain. Then stain the outer pieces and glue it all together. The outer pieces look like ash to me. Just be careful not to stain the edge that will receive glue.

Thankyou very much. Ill give that a try.

I dont know when I will be doing this project, but when I do I will try and post to show how it goes :) 

Masking will be ok. The difficulty in glueing up that sort of thru neck bass is that you will inevitably get squeeze out and slight misalignment between the wings and the neck. That will require planing/sanding afterwards to level.

Mask the (looks like ash to me) wings beforehand and you can apply a grain filler/shellac to the maple/walnut laminated neck section (for the bass shown). That will minimise any bleed thru. Carefully applying the stain after masking the centre neck section with blue tape will be ok. I've made many thru necks and been successful with this method. 

For the coffee table I made, I stained the pieces after glue up. I masked the surrounding areas with blue tape, and simply applied the stain. I had no bleed through. And it was the only way to ensure a level surface.

 

Does the glue between the boards act as a barrier to keep the stain from bleeding thru? Would the tape work if you want to stain only part of the same board?

Does the glue between the boards act as a barrier to keep the stain from bleeding thru? Would the tape work if you want to stain only part of the same board?

Tape worked very well on the test piece I made. I wasn't careful at all, and only had a minor seepage.

12281599_10208235969805101_1122424111_o.

And that's not laminated but one piece of wood?

And that's not laminated but one piece of wood?

One piece, put a piece of blue tape on and applied some stain with a foam brush. 

And on spalted at that! Who'd a thunk it? Thanks

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.